The design of engineering structures using frame structure, structural framework for the calculation according to the vertical load-bearing analysis.
本工程结构设计采用框架结构，结构计算按纵向框架承重分析。
The study presented the status of force bearing analysis on the swinging rotor of expander, and the calculation of stress and deformation was carried out on the key component-swinging rotor.
研究给出了膨胀机摆动转子进行受力分析情况，对关键部件摆动转子进行了应力与变形的计算。
The detailed load bearing analysis of a common foundation form in which the underground parking lot foundation is lower than the connecting multi-storied high-rise building foundation is provided.
对于目前较为常见的地下车库基础低于相连多高层基础标高时的基础型式，进行了较详细的受力分析。
Secondly, analysis and research of control arithmetic of magnetic bearing .
分析和研究了磁力轴承控制器控制算法。
The appropriateness of selection is still bearing failure analysis must be considered.
选材是否得当仍然是轴承失效分析必须考虑的因素。
This paper presents the application of wear particle analysis to the study of the effect of a particular factor (e. g. ionitriding temperature) on bearing failure.
本文介绍了磨损粒子分析在研究特殊因素(如离子氮化温度)对轴承失效的影响中的应用。
The foregoing analysis relates to very wide bearing only.
上述分析只适用于很宽的轴承。
Summed up is the process of the crack treatment on spot, the theory analysis and the design improvement of the hugging-bearing box body (HBBB) for SS7-type electric locomotive.
全面总结了韶山7型电力机车抱轴箱体在使用中发生裂纹的现场处理、理论分析和设计改进的过程。
The analysis results show that both the bearing capacity and settlement of composite foundation meet the need of engineering design.
分析结果表明，加固后的复合地基承载力和沉降量满足工程设计的要求。
The bridge axial alignment is a key point to bridge bearing capacity evaluation, disease analysis, health analysis and taking-over inspection.
桥梁轴线线形测定是桥梁承载力评定、病害分析、健康状态分析及竣工验收的重要环节。
Finite element analysis shows that there are three stress concentration areas inside the bearing.
有限元分析表明，轴承内部存在三个应力集中区域。
In the processing process in the bearing ring, through to the grinding crack mechanism analysis, the effective measure of control grinding crack was adopted.
在轴承套圈的磨加工过程中，通过对磨削裂纹机理的分析，采取有效的措施控制磨削裂纹的产生。
With analysis of structure of cone roller bearing inner ring forgings, corresponding improvement on original forging technology has been put forward.
分析圆锥滚子轴承内圈锻件结构，对原锻造工艺中的不足提出了相应的工艺改进措施。
This supply the helpful theoretical tools for nonlinear dynamic analysis and design of rotor-elliptic bearing systems in rotating machines.
为旋转机械转子-圆柱轴承系统的非线性动力学分析和设计提供了必要的理论基础。
In order to prepare statistical technology for the property analysis of bearing estimation, the statistical property of single vector sensor must be studied first.
为了给方位估计的性能分析预备必要的统计知识，必需首先研究单矢量传感器互谱估计的统计特性。
Raw material quality factor in the bearing failure analysis, the proportion has decreased significantly, but it is still bearing failure , one of the main factors.
原材料质量因素在轴承失效分析中所占的比重已经明显下降，但它仍然是轴承失效的主要影响因素之一。
Two types of effective structure of bearings were given based on the structure analysis of the bearing.
并在对电动机轴承组进行结构分析的基础上，给出两种有效的轴承组结构。
From analysis of combined needle roller bearing, the estimating formula of basic dynamic load rating for above bearing is derived.
从滚针组合轴承结构分析着手，推导出滚针组合轴承的基本额定动负荷估算公式。
According to our motor sliding bearing of the analysis and calculation think, sliding bearing fault and the selection of sliding bearings has the very big relations.
根据我们对电机滑动轴承的分析和计算认为，滑动轴承的故障与滑动轴承的选用有着很大的关系。
After that, this dissertation expatiates on the principles of structure design and the method of choosing parameters of axial bearing and discusses the analysis of strength and thermal verification.
对轴向轴承的结构设计原理及其参数的选定进行了具体的阐述，其中对强度分析和热校核也一一进行了讨论。
The analysis results from roller bearing signals with inner-race or out-race faults show that the diagnosis approach could extract fault characteristics effectively.
对滚动轴承的内圈、外圈故障信号的分析结果表明本文方法可以有效地提取滚动轴承故障特征。
Considering radial load, axial load, centrifugal force and gyroscopic moment acted on the ball bearing simultaneously, an analysis model based on quasi-dynamic method was set up in this paper.
本文利用拟动力学法，同时考虑径向负荷、轴向负荷、自身离心力以及陀螺力矩作用的影响，建立了高速滚珠轴承载荷分布的分析模型。
Bearing capacity analysis based on the upper bound theorem of plasticity could be numerically performed by element integration method.
基于塑性力学上限定理的地基承载力分析，在数值上可以通过单元集成法来实现。
This paper has described and analyzed the reason of the damaged bearing by means of chemical analysis, the determination of the hardness as well as the metallographic analysis.
本文介绍采用通过化学成分分析、硬度测定及金相组织检测等手段，对轴承损坏原因进行分析的情况。
Based on the field loading tests and FEM numerical simulation analysis, the paper probes into the potential bearing capacity of large diameter and super-long bored-cast-place piles.
基于入和没入硬层时有限元数值模拟对比分析和持力层不同时同场地现场对比试验资料分析，对大直径超长灌注桩的承载潜力问题进行了探讨。
Through analysis and practice to bearing ring double face grinding process, the proper methods of grinding wheel adjustment, grinding amount arrangement and product quality control were summarized.
通过对双端面磨削过程的分析和实践，总结出适当的调整砂轮和安排磨削量及控制产品质量的方法。
Two types of effective structure of bearings are given based on the structure analysis of the bearing in motor.
并在对电动机轴承组进行结构分析的基础上，给出两种有效的轴承组结构。
Two types of effective structure of bearings are given based on the structure analysis of the bearing in motor.
并在对电动机轴承组进行结构分析的基础上，给出两种有效的轴承组结构。
应用推荐