The new phase will extend this to pitch and yaw for all-axis control.
后面的阶段，将进一步延伸到飞机倾斜和偏航时翻滚轴的控制。
Therefore, the use of multi-axis control of SERCOS bus will be the future trend.
因此，利用SERCOS总线进行多轴控制将是未来发展趋势。
The interpolator is integrated into a CNC system with multiple axis control simultaneously.
并将该插补器集成在多轴联动数控系统中。
Normally, three or more SGCMGs are used in the spacecraft in order to realize 3 axis control.
在航天器的姿态控制中，通常采用三个或以上的SGCMG，以满足三轴控制的要求。
After measuring and debugging, the structure of elevation axis control system is founded out.
通过测试分析和调试，确定了俯仰轴伺服控制系统的结构。
Aiming at multi-axis control in logarithmic curves, an odd-even steps interpolation algorithm was designed.
针对对数曲线的多轴联动控制，设计了奇偶步插补算法。
At the same time, an one-dimension compound-axis control system is designed. Based on the system, an experiment has been carried out.
同时，本文设计了一个一维复合轴控制系统，对复合轴系统进行了实验。
Even then, by utilizing multiple layers in the design, a certain amount of Z-axis control can be accommodated, although not a full 3d pattern.
即使它不是一个完整的3d图案，特定数量的Z轴控制也能够适应多层结构的设计。
The results of experiments show the structure control increase the precision of elevation axis control system, and satisfies well engineering...
实验结果表明变结构控制方法提高了俯仰轴伺服系统的控制精度，满足了工程实际的要求。
Finally, a strict operational experiment of axis control was carried out by implementing the user mode application and the result of the test was obtained.
最后，通过编写轴控制系统用户态程序，本文完成了轴控制的实际运行实验，并给出了实验结果。
To set the proper parameter of register and on-chip ram of TMC428, it can make TMC428 control three stepper motor in the same time, and realize three-axis control system.
通过设置TMC428内部参数寄存器和片内ram的值，可使TMC428能够同时控制三个步进电机，实现三轴控制系统。
Simulation and experimental results show that the tracking accuracy of the main axis control system is not bigger than 1 Angle minute and this fulfills the demands of ATP system.
仿真和实验结果表明，主轴控制系统的跟踪精度在1以内，满足AT P系统对精度的要求。
If you don't need as much control over parsing, you may find a marshalling component — such as JAXB, Castor, or Axis — more convenient.
如果不需要更多地控制解析过程，可以找到更方便的编组组件，如JAXB、Castor或Axis。
1a. With an additional control laser of very high intensity applied transverse to the cavity axis, the single-atom EIT condition is achieved and maximum transmission is recovered See Fig.
当在另外一束与光腔轴线成横向垂直的高强度激光照射下，满足该原子所需的电磁感应透明条件，光会恢复到最大输出通量(图1b所示)。
Control about each axis is provided by manipulating hinged control surfaces on the aircraft.
通过控制在飞机上铰接在一起的控制板来控制每个轴。
These receptors control the activity of the hypothalamo-pituitary adrenal (HPA) axis, an endocrine system that is activated in response to stress.
这些受体可以控制下丘脑-垂体-肾上腺（HPA）轴的活性，HPA轴是一个对应激产生反应的内分泌系统。
Both the transition process and the tracking accuracy of the auxiliary axis can be improved by the fuzzy control method and the corresponding experimental data are given.
本文介绍一种既能改善子轴的过渡过程，又能保证子轴的跟踪精度的模糊控制方法。并给出了相应的实验数据。
The axis attribute allows you to specify the layout orientation, either along the X-axis or the Y-axis, while the spacing attribute allows you to control the spacing between components.
axis属性可用于指定布局方向，它的值可以是x - axis或y - axis，而spacing属性可用于控制组件之间的间距。
Roll axis - Longitudinal axis, passes through the airplane from front to rear - wing up and wing down control is by ailerons and flight spoilers.
横滚轴—又称纵轴。由飞机的前部通向后部。机翼下运动由副翼和飞行扰流板控制。
The orientation of the floor plan responds directly to the original pier axis and is an overall site control datum.
平面图的方向直接回应原始的窗间壁的轴线，是整个基地控制的基线。
Parsons recommended a method of automatic machine control that would guide a milling cutter to produce a "thru-axis curve" in order to generate smooth profiles on work pieces.
为了在工件上加工光滑的轮廓，帕森提出了一种自动的机床控制方式，它能够引导铣床刀具加工出一种“过轴曲线”。
Virtual axis machine tool, Structural Form, Kinematics Analysis, Control System.
虚拟轴机床，结构型式，运动学分析，控制系统。
The method I developed requires no eyepiece and no control of the RA axis movement.
小弟开发的方法，不需要接目镜， 也不用可以控制赤经轴的移动。
As illustration, these models are applied to an attitude control dynamics simulation of a three-axis stability satellite and the corresponding toques were plotted in curves.
为验证模型有效性，将其应用于某三轴稳定对地定向卫星姿态动力学仿真中，得到了相应的太阳光压干扰力矩曲线。
And according to the mathematical model, vector control principle and minimal direct axis current control and its digital realized method were discussed.
结合数学模型，讨论了有关矢量控制的原理和直轴电流最小控制的数字实现方法。
An adaptive fuzzy integral type sliding mode control method based on GA was proposed to control single-axis motion control system with nonlinear dynamic friction.
提出一种基于GA的自适应模糊积分型滑模控制策略，并将其用于具有非线性动态摩擦力的单轴运动控制系统中。
Roof released elevation of the line of control and the loading axis auxiliary line.
复验安装定位所用的轴线控制点和测量标高使用的水准点。
Roof released elevation of the line of control and the loading axis auxiliary line.
复验安装定位所用的轴线控制点和测量标高使用的水准点。
应用推荐