ASTM standards are well known in China.
目前ASTM标准在中国具有很高的知名度。
ASTM electrical standard is a absolute system.
ASTM的电工钢的标准是单独成体系。
The color is determined according to ASTM D1686-61.
颜色被依照美国材料试验学会D 1686- 61决定。
An American Society for Testing and Materials (ASTM) label.
美国检测与材料协会(ASTM)的标签。
ASTM A194 nuts of corresponding material are recommended.
推荐采用相应材料的ASTMA194螺母。
All field splices were bolted using ASTM A325 hex head bolts.
所有现场拼接都用美国材料试验协会的A325六角形头螺栓。
Nuts may be of the same material or may be of compatible grade of ASTM A194.
可以采用相同材料的螺母，或者可以采用可兼容的ASTM A194等级材料。
The test methods and numbers should meet the ASTM-D1000 required by clients.
测试方法与数值依客户所要求的ASTM-D1000所得。
Hence, the method here proposed may be considered as a supplement to ASTM E647.
因此，从方法上来说，可以看作是ASTME647方法的一个补充。
These tests are gross cleanliness inspections as stated in the ASTM Standard A 380 (1996).
如ASTM标准A 380 （1996）中所述这些检测只是清洁的粗检查。
The ASTM Standard a 380 (1996) refers to these acids as cleaning acids, not passivating acids.
ASTM标准a 380(1996)将这些酸归为清洁用酸而不是钝化用酸。
ASTM D2197-98 (2002) Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion.
美国材料试验协会ASTMD2197- 98(2002)《有机颜料在刮擦下的附着性标准测试方法》。
Our application of magnesium alloy ASTM standards to ensure the consistency of chemical composition.
我们应用ASTM对镁合金的标准来保证化学成份的一致性。
The impact property of U-PVC profile was evaluated in quantification by ASTM d4226-99 testing method.
用astmD4226—99冲击试验方法对聚氯乙烯异型材冲击性能进行量化评价。
This is an example of where the matching nut is not always explicitly called out in the ASTM standard.
这是一个例子，那里的配套螺帽并不总是明确要求指出，在ASTM标准。
Road Bike: Riders are required to wear ASTM, ANSI or SNELL approved helmets and obey the rules of the road.
道路自行车：骑手们被要求穿ASTM，ANSI或敏捷的同意的头盔并且服从交通规则。
The mechanical properties of mixed powder specimens were nearly equivalent to the ASTM for the PM compacts.
混合粉末样品的力学性能几乎达到美国ASTM粉末冶金的标准。
Flanges, unions, and valves not included in the scope of other ASTM specifications are specifically referenced.
法兰，管接头，以及阀门不包括在其它特别引用的ASTM规定范围内。
Heavy Hex bolt. Meets ASTM A307B standard. Application: Carbon steel material for use in bolting and anchoring applications.
重型六角螺栓，符合ASTMA307 B标准，应用：螺栓、锚固应用的碳钢材料。
ASTM E970 Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source.
ASTME970使用辐射热能源评定暴露的阁楼地板绝缘的临界辐射通量的试验方法。
A characterization approach for petroleum fractions based on the ASTM distillation data and the overall density has been proposed.
本文提出了一种从镏分恩氏蒸馏数据和总体密度对石油馏分进行假组分切割和物性估算的方法。
The pump casing, impeller, motor housing and stationary base elbow shall be manufactured of close-grained cast iron, ASTM A48, Class 30.
泵壳，叶轮，电机壳和固定底座弯头都应该采用符合美国材料试验协会ASTMA48级别30致密铸铁制造。
In ASTM D244, the density cup is a stainless steel measurer of known standard volume, but the shape and the dimension was not presented.
在ASTMD244中，密度杯为已知容积的不锈钢制标准容器，却没有具体的几何形状及尺寸；
Reference standard: USA ASTM-D999 and European rule. Equipment characters: high precision, low noise, easy parting, convenient performing.
根据美国ASTM -D999及欧洲相关标准，设备特点：高精度、低噪音、易装拆、方便操作。
Hoses meet 25/50 flammability and smoke development classification requirements of codes and specifications when tested by ASTM E 84 method.
符合25/50可燃性和发烟等级要求的规定，经过美国试验材料学会E 84方法检测。
Where austenitic bolting materials have been carbide solution treated but not strain hardened, they are designated Class 1 or Class 1a in ASTM A193.
在此，奥氏体螺栓材料经过碳化溶液的处理，但是没有经过应变硬化，因此归在ASTM A193的类别1或类别1a。
Manufactured strictly in accordance with all applicable ASTM specifications, these units have become the industry standard for close, accurate readings.
严格按照所有适用ASTM标准制造，已成为密闭、精确读数的行业标准。
Test method for ASTM D149 solid electrical insulating materials at commercial power frequencies the dielectric breakdown voltage and dielectric strength.
ASTM D149固体电绝缘材料在工业电源频率下的介电击穿电压和介电强度的试验方法。
Are all soldering related and referenced specifications current and available? For example: IPC, SAE, AIAG, ASTM, General Motors, Honda, Ford, and Chrysler.
是否所有焊接有关的和引用的规范当前可用版本？例如IPC,SAE,AIAG,ASTM，通用汽车，本田，福特和克莱斯勒。
Are all soldering related and referenced specifications current and available? For example: IPC, SAE, AIAG, ASTM, General Motors, Honda, Ford, and Chrysler.
是否所有焊接有关的和引用的规范当前可用版本？例如IPC,SAE,AIAG,ASTM，通用汽车，本田，福特和克莱斯勒。
应用推荐