No detectable pits or gray edge by visual inspection after coating.
在镀膜后表面无可察觉的陷坑或灰色边缘。
Besmear after coating moisture volatilizes then becomes rubber shape of elastomer waterproof layer.
涂刷后，涂膜水分挥发后即成为橡胶状弹性体的防水层。
The characteristic parameters of the grating are also measured before coating and after coating respectively.
对光栅在涂覆前后分别作了特性参数测试。
After coating, the film flowing down immediately, resulting in the phenomenon of uneven surface of the coating.
涂装后，漆膜立即向下流淌，造成涂层表面不均匀的现象。
Results After coating Ti, the surface of Ni-Cr alloy looked light golden without particles, blisters and fragments.
结果镍铬合金经涂钛后，表面无起皮、鼓泡、剥落现象。
After coating a substrate having heat resistance with a silane coupling agent, a layer having functionality is formed.
在用硅烷偶联剂涂覆具有耐热性的衬底后，形成了具有功能性的层。
The peak gain wavelength will cause blue shift of some ten nanometers after coating with the injection of the same level.
在相同的注入水平下镀膜后峰值增益波长会产生几十纳米的蓝移。
Results showed that the fluidity of the liposomal membrane after coating with the two macromolecules had no obvious changes.
可见，胶原蛋白、壳聚糖包覆脂质体能够在基本不干扰脂质体膜流动性的情况下，明显地提高其体外的稳定性。
Further, after coating a substrate having heat resistance with a silane coupling agent, a layer having functionality is formed.
另外，在用硅烷偶联剂涂覆具有耐热性的衬底后，形成了具有功能性的层。
Development complete in 48 hours after coating film, if there is ample humidity in workshop, it must be finished within 12 hours.
涂覆后需在48小时内显影，若操作场所温湿度较大，需在12小时内完成作业。
Development should be finished in 48 hours after coating, if there is ample humidity in work shop, it must be finished within 12 hours.
涂覆后需在48小时内曝光显影，若操作场所湿度较大，需在12小时内完成。
The team measured the electronic properties of a thin film made of zinc oxide nanoparticles before and after coating its surface with aluminum oxide.
这个团队测量了在由氧化锌纳米颗粒构成的薄膜表面上涂敷氧化铝前后的电子性质。
The experimental results show that after coating the single residual reflectance was reduced from 2.5% to 1.2% and could withstand the muggy and rain testing.
实验结果表明，镀膜后其单面剩余反射率由未镀膜时的2.5%减少到1.2%，并能承受湿热和雨淋测试。
Methods:Samples were dried at room temperature after coating films, followed by freezing, hardening. 4% acetic acid was used to extract metals in treated samples.
方法：试样经涂膜使用温度下干燥、冷冻硬化粉碎，4%乙酸浸泡处理，石墨炉原子吸收测定胶粘剂可溶性钡、镉、铬、铅含量。
As a result, after coating, both fabrics dyed with Acid Orange 7, Reactive Red KD-8B or Direct Red f, their fastness in particular sunlight fastness was improved greatly.
试验结果表明，经复合膜整理后，无论用酸性橙7、活性红kd 8b，还是直接红f染色的两种织物，色牢度特别是日晒牢度均有较大改善。
Twenty samples are coated on 20 different optical self-encoding microbeads respectively. All beads were mixed after coating and washing for multi-samples ELISA mix-screening.
将20种光谱自编码微球与20种不同物种的免疫球蛋白和血清样品一一对映包被，然后将其全部混合在一起，进行多样品混合ELISA筛选。
After being exposed to air during digging, the coating under the paint began to fall off.
挖掘过程中经暴露在空气中后，油漆下的涂层开始脱落。
After cutting, some may need to be deburred, some need to be bent; while other flat parts are just sent directly to powder coating, assembly, or directly to packaging.
切割完毕之后，有的需要去毛刺，有点需要折弯，有的平板零件只需直接送去喷涂，装配，或者直接打包。
A fine coating of resin is done after the painting in order to make a shining appearance.
在画完之后涂上薄薄的一层优良树脂，为了让它表面看起来闪闪发亮。
Soon after they died, the waxy coating began to decompose, releasing carbon-rich substances called fatty acids.
当它们死亡后，这个蜡质外层开始降解，释放出富含碳元素的脂肪酸。
The yellow you see coating its body is pollen, perhaps acquired after a messy tussle with a bee.
附着在它身体表面的黄色的东西是花粉。或许这只蜘蛛在和一只蜜蜂进行混乱的厮打之后而沾上的。
Paint coating finish and only after complete curing effect to confirm product quality.
涂料只有涂装完成并完全固化后的效果才能确认产品质量好坏。
Production process: after casting, extrusion, tinting, electrophoresis, powder coating, fluorine carbon spraying, mould, polishing, wood, metal wiredrawing, such extrusion.
生产工艺：经过熔铸、挤压、氧化着色、电泳、粉末喷涂、氟碳喷涂、模具、抛光、木纹、拉丝、钣金等挤压而成。
Corrosion under a scribe line or an area of damaged coating or edge, after salt spray testing or other testing.
在盐雾试验或其它试验后沿着划线涂层边缘的腐蚀。
If a longer time out, it should be made to pump from the Wells to carry out maintenance, rust, coating for oil and parts, after assembly storage preservation.
如果停用的时间较长，就应把水泵从井中提出来，进行维修、除锈、涂油及换件，组装后入库保存。
After Plating, cleaning the coating with the corresponding removers.
电镀后，请用相应清洁剂除去涂层。
Assembly and transport of components to GEWE or the construction site may only take place after the coating system has hardened.
部件组装及运输至GEWE或建筑现场的工作仅能在涂层系统完全硬化后才能进行。
Meanwhile, high surface hardness after heat treatment, the coating surface formed into the amorphous and crystalline mixture, the hardness is up to 1200hv.
同时表面硬度高，经热处理后，其镀层表面形成非晶态和晶态的混合物时，硬度可达1200 HV。
After the coating solidifying, the pipe test should be done with defect detector under the specified voltage.
待涂层固化当前，要应用缺陷检测器在涂料技术标准中规定的电压下对钢管进行检测。
Usage: After cleansing, coating on the skin massage gently till fully absorbed.
使用方法：洁肤后，涂于皮肤上轻轻按摩至完全吸收即可。
应用推荐