输送皂角泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.
戒指(材料见表6.1)的热以不同的方式处理根据齿轮上的戒指，在载有最高负荷区接触压力的压力。
The rings (for materials see Table 6.1) are heat-treated in different ways according to the strain on the gear rings and the contact pressure of the area carrying the highest load.
齿轮泵若是第一次运行，或长期闲置后再使用，最好在空载或小负荷情况下先跑合一小时左右。
If the first gear pump operation, or long-term idle after use, preferably in small load or no-load circumstances Xianpao One hour.
负荷和减速齿轮延长寿命。
Load and reduction gears are machined and hardened for long life.
泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
There are well-designed pump drain back tank and is exposed in the work gear torque exerted the smallest, so bearing loads of small, wear, pump efficiency.
混合器传动由一个坚固的非专利设计的平行螺旋齿轮减速机组成，最小的机械过负荷因子为1.5。
The agitator drive is comprised of a robust non-proprietary reducer which utilizes parallel helical gearing and has a minimum mechanical service factor of1.5.
对兰炼研制的680中、重负荷工业齿轮油的研究进行了阐述。
The study on 680 medium & heavy-duty industrial gear oils developed by LPPCC was described.
三网拍间和一个大辅助口袋里球拍的空间提供负荷和齿轮。
Three racquet compartments and a large accessory pocket offer loads of room for racquets and gear.
而在目前的瞬变，即使负荷搬迁是一种低频率的现象，一个相当小的瞬态是观察在高频率地区有缺陷的齿轮。
Whereas in the current transients, though load removal is a low-frequency phenomenon, a very small transient is observed at high-frequency regions for defective gears.
泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.
泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
Pump discharge of oil with reasonable design, gear oil and back at work under minimum torque force bearing load, so small, wear small, pump with high efficiency.
工业用密封式圆柱形，螺旋纹与锥形齿轮传动装置，特别是在采矿、化学加工，冶金和造纸业等方面的重负荷应用。
Industrial sealed with conical cylindrical, swirl, especially in gear transmission device, chemical processing, metallurgy, mining industry and heavy load, etc.
本文介绍了硫磷型N320中负荷工业齿轮油的研制及应用。
The preparation and application test of phosphorus-sulfur type N320 medium load industrial gear oil are described in this paper.
齿轮减速机的最少的机械过负荷因子为1.5。
The minimum mechanical service factor of the gear reducer is 1.5.
论述了新一代重负荷齿轮脂的研究，包括其组成、性能、应用。
Study of new generation lubricating grease for heavy - duty gear has been discussed elaborately, including its composition, performances and applications.
在高速重载下工作的齿轮，一般都承受较高的热负荷，故温度较高。
The gears operating at high speed and heavy load have to endure more heat and higher temperatures.
根据罗茨风机齿轮、轴受力情况，分析高负荷下风机齿轮轮齿折断及叶轮擦墙板的原因。
The cause which result in breaking off gear teeth and vanes touching wall on high load are analyzed, according to the stress status of gear and axle in Root's blower.
如果高粘度齿轮泵的工作压力调整过高，则会使齿轮泵在超负荷下运行。
If the high viscosity gear pump high pressure adjustment, will make the pump running under overload.
油都用在高负荷工业齿轮系统，如直齿圆柱齿轮，锥齿轮，行星齿轮和蜗轮副。
GEARMASTER PGP oils are used in high-load industrial gear systems such as spur gears, bevel gears, epicyclical gears and worm gear pairs.
齿轮泵带负荷停车时，亦可防止泵倒转而在其输出管道内产生局部真空。
Gear pump to stop loading machine, can be in the output pipe to prevent pump reverse, and create a partial vacuum.
然齿轮箱又重(达16吨)、又贵，同时也增加机舱及塔架基座的负荷。
So most of wind turbine is equipped with gearbox, but gearbox is heavy (16 tons) and expensive, also it increases the loading of nacelle and tower foundation.
某带行星齿轮减速器的发电机组在满负荷额定转速工况下，出现减速器轴承及发电机后轴承处横向振动偏大的故障现象。
Under the condition of rated load and rated speed operation of a generator set, over-vibration phenomena appeared in the planetary gearbox's bearing and the rear bearing of the generator.
齿轮泵若是第一次运行，或长期闲置后再使用，最好在空载或小负荷情况下先跑合一小时左右。
Gear pump is the first run, or long-term idle before using, had better under the condition of no load or small load to run one hour or so.
齿轮泵若是第一次运行，或长期闲置后再使用，最好在空载或小负荷情况下先跑合一小时左右。
Gear pump is the first run, or long-term idle before using, had better under the condition of no load or small load to run one hour or so.
应用推荐