系统的硬件平台主要由数据采集卡和霍尔电压电流传感器构成的信号调理器组成。
The hardware is made up of Data Acquisition card (DAQ) and signal conditioning extension for instrumentation (SCXI) which is composed of Hall voltage current sensor.
以霍尔电压及失调电压的状态为出发点，提出了一种更简单的霍尔信号再生电路设计方案。
Based on analyzing the status of hall and offset voltage, a completely new and comparatively simple hall signal regeneration circuit was brought forward.
本文分析了霍尔电压测量过程中出现的因不等位电压过高而引起的异常现象，并提出了解决办法。
The paper analyses the irregular phenomena occurring in measuring Hall - voltage due to too high voltage in inequal position and presents a solution to it.
在A1210 - A 1214霍尔效应锁存包括一个单一的硅芯片上以下内容：稳压器，霍尔电压发生器，小信号放大器，施密特触发器和NMOS输出晶体管。
The A1210-A1214 Hall-effect latches include the following on a single silicon chip: voltage regulator, Hall-voltage generator, small-signal amplifier, Schmitt trigger, and NMOS output transistor.
介绍闭环霍尔电流和电压传感器的基本工作原理。
The closed loop Hall current and voltage sensors' principle was introduced.
利用电压比较器，设计出了霍尔效应式电子点火控制电路。
Hall effect type electronic ignition control circuit has been designed by means of voltage comparator.
本文介绍一种不用恒流源而直接用电压源为霍尔元件供电的方法。
This article introduces a method of direct usage of voltage source as a power for Hall element instead of constant current system.
通过该铜制电流路径施加的电流能够生成可被集成霍尔ic感应并转化为成比例电压的磁场。
Applied current flowing through this copper conduction path generates a magnetic field which is sensed by the integrated Hall IC and converted into a proportional voltage.
利用霍尔传感器完成电压、电流的采集，并送led显示器显示。
Hall sensor is used to collect voltage and current signal, and the collected result displayed by LED displayer.
系统采用霍尔传感器和电压传感器对电压和电流采样，转化成电压信号输给压控芯片LM 231。
The Halls sensor and voltage sensor is used for sampling current and voltage in the system, and the signals are transformed into voltage signal and sent to the LM231.
借助输出电压采样和霍尔元件，设计了电流、电压反馈电路，形成了闭环控制系统。
A closed loop control system is formed by current and Voltage feedback system by means of HALL sensor and potentiometer.
并通过对动态测量中某霍尔位移传感器位移-电压数据进行了坏值剔除和三次多项式非线性拟合，表明动态测量中传感器数据的非线性处理方法。
The curve of a Hall displacement sensor is obtained by polynomial fitting. The method of data erasing and curve fitting can be applied in processing the data of sensor in dynamic measurement.
给出了一种利用霍尔效应测量螺线管磁场的新方法：用数字电压表取代电位差计等诸多仪器测量霍尔电势差，进而计算出通电长直螺线管内轴向磁场的分布。
Digital voltmeters, instead of voltage meters and other instruments, are used to measure Hull voltage and then to calculate the axial magnetic induction distribution in charged straight spiral tubes.
给出了一种利用霍尔效应测量螺线管磁场的新方法：用数字电压表取代电位差计等诸多仪器测量霍尔电势差，进而计算出通电长直螺线管内轴向磁场的分布。
Digital voltmeters, instead of voltage meters and other instruments, are used to measure Hull voltage and then to calculate the axial magnetic induction distribution in charged straight spiral tubes.
应用推荐