可以用于铸造的材料类型有：铝合金、青铜、工具钢、不锈钢、钨铬钴合金、镍基合金和贵金属。
Thee types of materials that can be cast are aluminum alloys, bronzes, tool steels, stainless steels, stellite, hastelloys, and precious metals.
钨铬钴合金6阀座面，使用寿命更长。
这个品质钴钨环是免费，以避免过敏，而且有硬质合金，使其耐划痕。
This Quality Tungsten Ring is Cobalt Free to avoid allergies and it has the Carbide to make it Scratch Resistant.
这是钴钨环免费，为了避免过敏，而且有硬质合金，使其耐划痕。
This Tungsten Ring is Cobalt Free, to avoid allergies and it has the Carbide to make it Scratch Resistant.
钨铬钴合金面耐磨性优于13CR楔板，而且更易于维修和更换。
Stellite face will wear less than the 13 CR wedge, which can easily be repaired or replaced.
钨铬钴合金的硬度不会受到热处理的影响。
本文通过焊接试验、显微分析和磨损试验论述了以铬、镍、铁基合金代替钴、铬、钨合金作石油钻头牙爪堆焊耐磨合金的问题。
In this article we discussed the possibility of replacement of cobalt alloy by Cr-Ni iron Base alloy in drill bit bearing on the basis of welding test, wearing test and microscopic examination.
为了延长使用寿命，阀瓣可以涂上一层钨铬钴合金。
To extend the life of the valve flap can be coated with stellite.
研究了在镍钴合金镀液中加入碳化钨微粒形成镍-钴-碳化钨复合镀层的共沉积过程。
Composite electrodeposits of nickel-cobalt-tungsten carbide were prepared by adding tungsten carbide particles in the nickel-cobalt alloy solution.
报道了以钨酸钠、硫酸钴和二亚硝酸二胺铂为主盐、以柠檬酸盐为络合剂电沉积钴铂钨合金的工艺过程。
A series of cobalt platinum tungsten alloys were deposited with sodium tungstate and cobaltous sulfate as the main salts and citrate as the complex agent.
阀座环较长，并且是密封焊接的，能够补偿温度波动。阀座面用钨铬钴合金6硬化，研磨和层叠为镜面光洁度。
Seat rings are long to compensate for temperature fluctuations and are seal - welded. seating faces are hardfaced with stellite 6, ground and lapped to mirror finish.
介绍了用热的浓硫酸处理废硬质合金，回收金属钴和碳化钨的方法。
This article reports on a method of retrieving cobalt metal and tungsten carbide from hard alloy scrap by the sulphate method.
这种新牌号合金代用某些常用冷变形模具材料，如工具钢，钨钴合金，模具寿命明显提高。
When this new material is used as cold dies instead of the usual materials, such as tool steels or tungsten carbide, the life of these is longer.
钨铬钴合金面阀座，经过研磨抛光达到镜面抛光度。
结果表明，钨钴合金从孔隙底部致密地向上填充，能完全封闭孔隙。
The experimental results showed that W-Co alloy was compactly filled up from the bottom of holes, and the holes were sealed completely.
本文讨论了从钨钼混合丝(条)和合金残料等含钨废料中分离钨钼钴的化学溶解法。
The chemical dissolution methods to separate and recover tungsten, molybdenum and cobalt in tungsten scraps such as mixed W-Mo wires (bars) and alloy scraps are discussed.
实心钨铬钴合金6阀瓣，即使没有弹簧，也可适用于快速和完整阀座的全引导。
Solid Stellite 6 disc, fully guided for fast and full seating, even without spring.
适用于低温环境的钨铬钴合金阀座面的柔性楔板。
Flexible wedges with Stellite seating faces for cryogenic service.
加之钨钴合金本身的高硬度和高强度可以与硬质氧化膜较好地相配合，能有效地减小应力集中，膜层硬度也因此获得明显提高。
Besides, the hardness of W-Co alloy was compatible with the hard anodizing film. Stress concentration was effectively reduced, therefore the fil...
焊接连接阀座采用钨铬钴合金6阀座面。
高比重钨合金材料由钨粉末、镍粉末、铁粉末和钴粉末制成。
The high specific weight tungsten alloy material is prepared by tungsten powder, nickel powder, iron powder and cobalt powder.
它采用几个“档次”含有钨硬质合金和粘结剂不同比例(通常是钴)。
It is offered in several "grades" containing different proportions of tungsten carbide and binder (usually cobalt).
钨铬钴合金可以进行高度抛光，可用于钢阀门的密封环。
Stellite takes a high polish and is used in steel valve seat rings.
阀座面为钨铬钴合金，经过研磨抛光达到镜面光洁度。
阀座面为钨铬钴合金，经过研磨抛光达到镜面光洁度。
应用推荐