多物理量参数报警输出，可由用户任选其中之一；
With signal transfer output of several physical parameters, users can choose any of them.
一些函数的输入是数值，比如字符串函数的起始、长度和偏移量参数。
For some functions, a numeric value is input, for example start, length, and offset parameters of string functions.
通过匹配追踪算法寻找与回波信号最匹配的基函数来确定脱靶量参数。
Miss distance parameters are estimated by matching pursuit algorithm to search the basis function which best matches the echo signal.
对过量参数值由低值逐渐升至动作值，欠量参数值由额定值降至动作值。
Excessive parameters, increase gradually from low value to operation value, less of parameter values decrease from rated value to operation value.
用NLS求解的林木生物量参数的精度高于用LLLS求解的林木生物量参数的精度；
The precision of tree biomass parameters estimated by NLS is higher than that by LLLS;
需肥量参数具有较大幅度的变化，应按照土壤肥力以及产量目标来合理调整并确定这个重要参数。
There was a range for parameters of fertilizer requirement, so it should be adjusted according to soil fertility and yield.
结果根据不同摄影参数下的空间分辨率分布情况，获取优化的CR下肢全长摄影的管电压和毫安量参数。
Results Optimal tube voltage and milliampere parameters of the full-length leg projection was acquired in terms of the distribution of spatial resolution under different parameters of exposure.
研究了公差网络中的各公差对相应的旋量参数的约束不等式表示，从而构成了公差大小优化的不等式约束。
Screw parameters in VGCN specified by tolerances in TN are expressed as inequation, which is inequation constraint in optimization of tolerance values.
该控制器采用分段解析函数控制规则，函数运算结果直接作为输出控制量，简化了模糊处理过程，且使得输出控制量参数具有自调整能力。
Fuzzy Algorithm is proposed in this paper. The controller adopts subsection analysis function control rules. The result of the function computation directly ACTS as the output control variable.
所用的参数是您所期望的内爆效果量。
这些参数指向了一个字符串表中的偏移量。
您还可以对每秒钟的事务量进行采样，并调整该参数以适应每秒钟的峰值事务量(或者采用它的某个较大的百分比)。
You could also sample the number of transactions per second and adjust this parameter to accommodate the peak number of transactions per second (or some large percentage of it).
使用这样的宏可以显著减少代码输入量，因为不必不断地编写和重新编写变量绑定、派生和参数传递。
Using macros like this significantly reduces typing because you do not have to constantly be writing and rewriting variable bindings, derivations, and parameter passing.
字符串中的偏移量：LOCATE函数的第二个参数，指定了字符串中开始搜索的起始位置。
Offset within a string: The second argument of the LOCATE function, which specifies the starting position within a string to begin the search.
不管参数列表区域多大，被调用的函数总可以知道每个参数的精确偏移量。
This way, the function being called can know the exact offset of each parameter, no matter how big the parameter list area is.
这个函数返回一个信号量集标识符，它与一个参数的键值关联在一起。
This function returns the semaphore set identifier associated with the argument key.
请注意：这些数表示定义字段的参数结构中的偏移量。
Note that the Numbers represent the offset within the param structure where the fields are to be defined.
这个函数使用一个信号量对象的句柄作为参数，并会一直等待下去，直到其状态变为有信号状态或超时为止。
This function takes the handle to the semaphore object and waits until it is signaled or a timeout occurs.
函数pthread_cond_wait主要就是用于阻塞线程的，它有两个参数；第一个是一个指向条件变量的指针，第二个是一个锁定了的互斥量。
The function primarily used for this is pthread_cond_wait . It takes two arguments; the first is a pointer to a condition variable, and the second is a locked mutex.
在这两种方法中，不赞成使用参数结构，因为它强加了限制：指定在内存中，每个参数必须位于 param_struct中的特定偏移量处。
Of these, param structure is deprecated as it imposes restrictions by specifying that each and every parameter has to be at a particular offset within param_struct in memory.
start - index参数，指定条目的起始偏移量。
The start-index parameter, which specifies the start offset for the entries.
start - index参数指定提要的开始偏移量。
The start-index parameter, which specifies the start offset for the feed.
时间偏移着色器具有参数“数据名称”，以确定从哪个用户数据获取偏移量。
The timeshift shader has the parameter "Data Name" to determine from which user data the offset is taken.
分析了不同加工参数对被加工内圆表面粗糙度和研磨量的影响。
Effect of different machining parameters upon the inner surface roughness and the removal rate was analyzed.
为表达过程时变的特点，引入时间参数作为神经网络的一个输入量。
The time parameter is also imported into the neural network to give the time-varying characteristic of the process.
参数值可以是任何有效的模板表达式，比如字符串字面量或组件的属性。
The parameter value can be any valid template expression such as a string literal or a component property.
从而成功地实现了对气压焊的焊接压力、气体流量、顶锻位移量等焊接过程参数的控制，并使控制系统具有较快的动态响应速度和较高的控制精度。
So the control of the welding parameter such as welding pressure, gas flux, upsetting length is realized, and the system has a high dynamic response rapid and a high control precision.
从而成功地实现了对气压焊的焊接压力、气体流量、顶锻位移量等焊接过程参数的控制，并使控制系统具有较快的动态响应速度和较高的控制精度。
So the control of the welding parameter such as welding pressure, gas flux, upsetting length is realized, and the system has a high dynamic response rapid and a high control precision.
应用推荐