采用软件滤波技术，提高了信噪比；
系统采用软件硬件双重保护。
采用软件校正，提高了测量精度和整机的可靠性。
Software calibration method is used to increase measuring accuracy and reliability.
采用软件并行查寻方式，提高系统快速响应能力。
The system's software adopts parallel searching mode, which improve the system's rapid response ability.
最采用软件编程的方法得到振动幅度和频率参数。
In the end, the software method is applied to get amplitude and frequency parameters of vibration.
采用软件实现方法的主要技术关键是确定PC控制算法。
Main technical key using the software achieving method is to determine PC control algorithm.
容错服务器具有处理性能高的特点，可以采用软件故障注入方式。
Fault-tolerant Server has the advantage of high processing performance, so software fault injection is adopted.
采用软件平台策略是一个根本性的改变，需要组织重新审视并调整已有的做法。
Adopting a software platform strategy is a radical change that requires the organization to revise and adjust its existing practices.
通过模拟的模糊运算，得出总控制表，采用软件查询的方法进行控制。
Through fuzzy operating and adopting the approach of software query on controlling, a total controlling table was finally obtained.
周期信号测量中广泛采用软件同步采样测量方法，其测量误差普遍存在。
Software synchronous sampling is widely employed in periodic signal measurement, but measurement errors occur very commonly.
同时，阐述了实现齿隙误差补偿的软件方法，并采用软件方法加以实现。
Meantime, an algorithm to the error compensation of the tooth clearance is implemented.
单片机应用系统中，除采取硬件抗干扰措施外，亦常采用软件抗干扰技术。
In the application system of MCU, some software anti-jamming techniques have been adopted besides some hardware anti-jamming measures.
通过对日照分析软件功能的介绍，论述了采用软件法在规划管理审批中的意义。
Introduces the functions of sunshine analysis software, discusses the significance applied the software analysis methods in city plan management.
根据误差模型及系数，采用软件进行误差补偿，有效地提高了测角系统的精确度。
The accuracy of angular displacement was increased greatly by software error compensation according to the error model and parameters.
本文采用软件无线电思想，建立了系统实现模型，并论证了系统模型的可实现性。
Using software radio, this paper set up a model of the system, and demonstrates the realization of the model.
针对邦元软件开发困难的现状，本文提出采用软件框架指导和辅助邦元程序开发。
In order to overcome the inconvenience of federate software development, we adopted software framework technology to guide and assist federate development in this paper.
而对目标的未来点解算、火炮随动和目标距离等环节则采用软件仿真模式来完成。
At the same time, the modules of the future position calculating of target, artillery following movement and target distance measuring are completed by the mode of software simulation.
另外，采用软件无线电能进行多载波处理，减少射频通道数，缩小体积，节约成本。
Additionally, another advantage of software radio is that it can process multi-carrier, decrease the RF channel, lessen the devices 'solidity, and save the its cost.
采用软件细分的方法，处理干涉条纹的移动量，得到被测点相对于准直光束的偏移量。
Movement of the interference stripes are dealt with by means of software subdivision, after that offsets of the spot to the laser beam is gained.
本文的意义在于采用软件方法实现了数字化调制与解调，它是基于PC机声卡来完成的。
The significance for this paper is to realize digitized modulation and demodulation by means of the software. It is based on the audio-card of PC.
本改进方法采用软件方式控制手机运行，简化测试系统硬件需求，降低系统搭建的难度。
The improved system utilizes software approach to control mobile phones, which simplifies hardware requirement and reduces the difficulty of system setup.
采用软件的子电路功能将相对复杂的时分秒电路进行了智能集成，使整体电路得到简化。
The complex hour, minute and second circuits can be intelligently integrated by the function of subcircuit.
对于控制状态失常问题采用软件冗余、设置当前输出状态寄存单元和设置自检程序等对策。
Lastly, the methods of software redundancy, setting present output state register unit, and setting self checking program to solve the problem of control state being out of order.
该方法采用软件细分、“虚拟变频”技术，实现了步进电动机多档位、带电自适应细分驱动。
Software subdivision and "virtual frequency conversion" technology were adopted in this solution, which realized multigrade, adaptive subdivided drive in operation of stepping motor.
该控制系统采用软件中断控制系统结构及子程序结构简单，条件明确在经济型数控中应用较多。
The control system USES software interrupt control system structure and subroutine is simple, clear in the economic conditions in the application of NC more.
将传统的等螺距误差补偿与机床使用情况相结合，提出并采用软件方法实现弹性螺距误差补偿。
A new software-based method for flexible thread pitch error compensation is proposed, considering the traditional equi-thread pitch error compensation and the usage of the CNC machine tools.
采用软件重用技术是解决软件危机的重要途径，基于组件技术的软件工程是重要的软件重用技术。
Using the technology of reuse software is an effective way to solve software crisis. Software engineering based on reusable component is a major approach of reusing software.
采用软件无线电技术的雷达导引头具有结构简单、可靠性高、易于维护升级、抗干扰性能强等优点。
The active seeker with software radio techniques has the merits of simple structure, high reliability, easy upgrade, easy maintenance and good anti-jamming capability.
脉冲频率调节采用软件延时或硬件定时，升降频采用直线升降法、指数曲线升降法或抛物线升降法。
The frequency of feeding pulses is regulated by software's delaying or hardware's timing.
接收端采用软件解压缩，软件算法融合了H·263/H·263+标准算法和图像增强与分割技术。
The software arithmetic mixed standard H. 263/H. 263+ arithmetic and image enhancing and dividing technology.
应用推荐