双击圆角矩形图层然后添加8白色描边，宽度为8px，混合模式为叠加然后调整透明度为30%，这样就会有一个很酷的透明效果- _。
Double click on the rectangle's layer and add an 8px white stroke. Change the Blend Mode to Overlay and drop the opacity to 30% to give a cool transparent effect.
双击圆角矩形图层然后添加8白色描边，宽度为8px，混合模式为叠加然后调整透明度为30%，这样就会有一个很酷的透明效果-_
Double click on the rectangle’s layer and add an 8px white stroke. Change the Blend Mode to Overlay and drop the opacity to 30% to give a cool transparent effect.
我们所要做的应该是将图片放置在幻灯片的顶层，然后将混合模式设为叠加，再将不透明度设为45%左右。
What we’re going to do instead is set it on top of the colored slide and set our blending mode to Overlay. Then throw your opacity to around 45%.
我们所要做的应该是将图片放置在幻灯片的顶层，然后将混合模式设为叠加，再将不透明度设为45%左右。
What we're going to do instead is set it on top of the colored slide and set our blending mode to Overlay. Then throw your opacity to around 45%.
现在，改变它的混合模式为叠加和50- 90%之间的较低层的透明度。
Now change its Blending Mode to Overlay and lower the layer's Opacity between 50-90%.
然后调整该图层的不透明度为20%并改变图层的混合选项为叠加。
Then reduce this layer's opacity to 20% and change the layer's blend mode to 'overlay'.
设置层混合模式为“叠加”，降低不透明度到65％。
Set this layer to "overlay" and reduce the opacity to about 65%.
另一个我常使用的窍门是给在最顶层添加一层，并在我希望的位置进行绘制，然后设置它的叠加方式为柔光，并降低它的透明度。
Another trick I like to use often, is to add another layer on top of everything and paint the general colors I want in each part of the image, then set it to soft-light and lower it's opacity.
再次复制这一层和改变混合模式为叠加，透明度50%。
Duplicate this layer again and change the Blend Mode to Overlay at 50%.
之后将混合模式改为叠加，不透明度为63%。
Change the blending mode to Overlay and reduce the opacity to 63%.
层类型改为叠加，并将层透明度设置为18%。
Change the layer type on Multiply and minimize the opacity till 18 %.
步骤4。将图层模式设置为“叠加”，并调整一下“图层1”的填充不透明度。
Step 4. Set the blend mode to 'Overlay' and change the fill opacity on 'Layout 1'.
这个光芒我是先给它添加一个低透明度的白色光，然后复制图层给它一个黄色叠加。
I did the glow by first giving it a white glow on low opacity, then duplicating the layer and giving it a yellow glow on Overlay.
在编辑过程中，49个片段都需要被编辑为一层层只有很薄的透明度的片段，最后，49个片段不断叠加，最终达到完全的不透明。
Each clip of the 49 clips will be adjusted to thin opacity in the edit. All 49 clips will be overlayed to make the total of 100% opacity.
将透明度修改为70%，设置融合模式为叠加。
Bring down the Opacity to 70%. Set the Blending Mode to Overlay.
将透明度修改为70%，设置融合模式为叠加。
Bring down the Opacity to 70%. Set the Blending Mode to Overlay.
应用推荐