用途：适用要求较高的微波器件，传感器，滤波器及航天，导弹上应用的元件气密性带压力保护的封焊。
Usage: suitable for air tight seal welding with pressure protection of microwave device, sensor, filter and components that used on spaceflight and guided missile that have high requirement.
在开发阶段制定的元件和原材料规格应多加考虑以适用于其使用目的。
Component and raw material specifications developed during the design phase should be well conceived and adequate for their intended purpose.
仅标出了继电器闭合或开路时适用的元件。
Only the applicable elements of a closed or open relay are shown.
利用建立在对称分量解耦-补偿理论基础上的电力元件模型，提出了适用于谐波潮流计算的网络模型和算法。
By using the power element models established on symmetrical component decoupling - compensation theory, a network model with algorithm suitable for harmonic flow calculation is developed.
因此，此电路特别适用于电阻式传感元件的信号处理。
The converter is therefore suited as a signal conditioner of a resistive sensor.
本文研究提出了一种适用于超高压电力系统的新型选相元件。
In this paper, a new type of phase selection element used for EHV power system is studied and suggested.
电子雕刻系统采用高频电—机械转换器作为记录元件，常用的光栅图像处理器不能适用。
Electronic engraving system USES electromechanical converter as its record component, therefore, the conventional Raster Image Processor are not suitable for the electronic engraving system.
该方法同样适用于其它各种圆形光学元件的涂布。
The method is suitable for method rubberizing any optical elements of circularity.
本标准适用于ISO米制螺纹平支承面的机械连接元件。
This standard applies to mechanical joining elements with metric ISO thread and flat head bearing surface.
它特别适用于大功率ASEA型继电器接插件，也可用于其他弹性元件。
It was suitable to be used in ASEA type high power relay as the elastic element of insert-pull pieces.
本文推导和研究了适用于高通量工程试验堆燃料元件燃耗测定的重要公式，并将ASTME244的公式作了重要修改。
In this paper, a set of important formulae for burnup determination of fuel element from HFETR are deduced and researched, and main formulae of ASTM E244 are reformed.
平整度好，精密度高。适用于各种精密电子元件、电路板、汽车及汽车轮毂、轴承内芯的精密抛光。
Good flatness. High precision. For precision finishing of electronic component, printing circuit board and core of precision bearing.
这一方法也适用于其它分立元件的励磁调节装置。
应用线性矩阵分析技术的特征值方法适用于悬挂元件均为线性变化并带有锥形踏面的车辆。
The eigen value method of matrix analysis technique is applied to the cars with all the suspension elements being linear change and with cone treads.
系列215也适用于墙安装流元件的压力供应场合。
The215is also suitable for pressure supply to wall attachment fluidic devices.
该模型基于功率注入法，考虑了所在线路的对地电纳，且直观、简单、通用，适用于FACTS元件的多种运行方式和所有的FACTS设备。
This model based on power injection method, is intuitive, convenient and versatile, and can be used for various functional modes of FACTS devices and all FACTS devices.
这一理论也适用于其它多端微波元件的分析。
This theory is also suitable for the analysis of other multi-port microwave devices.
介质常数为50 ~ 250，导磁率为50 ~ 100以上，适用于低成本的埋入微型无源元件。
Dielectric constant is 50 ~ 250. Permeability is 50 ~ 1100. It is suitable to burying miniaturization passive component in low cost.
本文对各种节流元件的工作原理、适用性和性价比进行分析。
Makes an analysis of the working principle, applicability, performance price ratio of different kinds of throttling elements.
适用范围：厨具、餐具、电子元件、集成电路、电器等行业。
Scope of application: kitchenware, tableware, electronic components, integrated circuits, electrical and other industries.
该电路适用于起始阻值漂移，而灵敏度基本不变的气敏元件，可大大提高此类元件的稳定性与准确性。
This circuit can greatly enhance stability and accuracy of gas sensors which have start resistance drift but basically constant sensitivity.
适用于各种扬声器及元件单点打胶。
It is applicable for single gluing of various loud-speakers and components.
适用于焙烧生产纯三氧化钼，还原钼粉，制造钼片、钼丝和钼元件。
Used in produce pure molybdenum trioxide, and subsequent reduction to molybdenum for manufacture molybdenum wire. molybdenum flat and molybdenum component.
适用于焙烧生产三氧化钼，还原钼粉，制造钼片、钼丝和钼元件。
Used in produce pure molybdenum trioxide, and subsequent reduction to molybdenum tor manufacture molybdenum wire. Molybdenum flat and molybdenum component.
仿真结果表明：所提方法对模拟电路的硬故障与元件参数偏移较小的软故障均适用，故障检测与定位准确率高。
The simulation results show that the proposed method can detect and locate catastrophic and parametric faults of tolerance circuits and has satisfactory diagnosis accuracy.
实验结果显示六棱柱元件能耗小、出料温度低、混合效果好，适用于玻璃纤维增强改性加工过程。
The results show that FTX polygon consumes less energy, the temperature of the polymer is lower at the exit of the extruder and its mixing ability is better than kneading block.
型送丝机构采用永磁直流电机作为驱动元件，结构简单、实用，适用于抽头式焊机配套使用。
MXN-10-D wire feeder is designed with magnet motor as its drive, advantages; usefulness and suppleness, suitable for TAP-TYPE welding machine.
此式不但适用于某一条电路，而且适用于电路中的任一元件。
The equation is applicable to a circuit as well as to a component in a circuit.
此式不但适用于某一条电路，而且适用于电路中的任一元件。
The equation is applicable to a circuit as well as to a component in a circuit.
应用推荐