预测输出和实际资料之间的差别(预测偏差)即为我们所求的有效信息。
The difference, between the predicted output and the observed data (prediction error) is the significant signals that we desire.
比例温度控制（P）是一种的连续温度控制方式，它的特点是输出与输入的偏差值成比例关系。
P is a kind of basic method to successive temperature controlling. Its characteristic is the deviation value in direct proportion relation that outputs and inputs.
在硬件电路设计上，防滑控制器采用TMS320F 2812和外围电路构成速度捕获电路，完成滑移率偏差的控制并输出刹车压力信号。
In hardware designing, TMS320F2812 and its peripheral circuit make up the velocity capturing circuit. Anti-skid controller controls slip ratio error and exports braking pressure signal.
函数发生机构中输出角度与期望值之间的最大偏差为最小的问题机构综合中一个典型而又较难处理的问题。
It is the typical and troublesome problem that the synthesis of function generator approaches minimization of the maxiumun deviation between the output and the expected value.
在测量力10%的侧力作用下力转换器的输出信号与所测力之间的相对偏差。
Relative deviation of the force transducer's output signal with measuring force as a result of lateral force at 10% of the measuring force.
另一方面它是基于偏差的，相对于基于输出等形式的解耦算法来说，其反映速度快。
On the other hand, the speed of algorithm based on error is faster than the decoupling arithmetic based on output.
针对数字控制技术的特点，分析了在选择性谐波消除法的理论计算结果与实际开关角数字控制结果出现偏差时，对逆变器输出电压谐波含量的影响。
This paper analyzes the influence of the error between the calculated results by selective harmonic elimination and the digit_controlled results on the output of inverter.
克服了线路阻抗变化对系统均流精度的影响。实验结果表明，该方法能较好地实现逆变模块的功率均分，模块间输出电流偏差小于1%。
The experimental results show the proposed method can share the output power quickly, and the current-sharing error is less than 1%.
传统SVPWM控制方式存在死区时间，使系统输出电压能力降低，出现相位偏差、波形畸变等现象。
Aiming at the phenomenon of reduced system output voltage capability, phase deflection and wave aberration of tradition SVPWM dead problem.
PID算法中采用功率补偿，解决了小偏差下PID算法输出功率不够的问题。
PID algorithm using power compensation to solve the problem of under the small deviations, the PID algorithm output power shortage.
该方法将实际输出电压和期望输出电压的比较偏差作为负反馈加到下一个采样周期的开关调制函数矩阵中。
The discrepancy between the actual output voltage and expected output voltage of the matrix converter is calculated and added to the switch modulation matrix in the next sampling period as feedback.
这事实验证了输出CADLL处理这个例子表明，该激光雷达的输出可以用来估计在测量路径偏差的可能性。
This fact validates the outputs of the CADLL processing and this example shows how the output of the LiDAR might be used to estimate the possibility of having multipath biases in the measurements.
迭代学习控制的基本思想是基于输出信号与给定目标轨迹的偏差不断修正不理想的控制输入信号，实现在有限时间区间的完全跟踪任务。
The idea of ILC is to gradually revise imperfect control input using the error between system output and the desired trajectory and realize perfect tracking in a finite time interval.
在静态条件下可以直接比较输入和输出数值，在动态条件下应排除时滞影响，分析输出和输入数值的随机偏差。
Deduced that the input data and output data can been compared directly under static condition, but the time delay must be excluded under dynamic condition and analyze the random error of the data.
对温度用模糊PID控制，以温度偏差和温度偏差变化为输入，燃料流量为输出，这个模糊控制器能满足控制要求。
The fuzzy-PID control used in temperature control, with temperature departures and the changes and as its input and fuel flow as output, could satisfy the control demand.
通过两输出电容电压的偏差改变电流参考给定来实现整流器输出中点平衡。
The problem of neutral-point balance is resolved by changing the amplitude of current reference according to the voltage error of two capacitors.
设计的模糊控制器以电机的转速偏差及转速偏差率为输入，输出量用于控制斩波调速时的导通角。
The fuzzy logic controller designed in this study determines the required angular used in the DC chopper control based on motor speed error and its change.
另外，该算法是在闭环系统下进行的，它能够检测出信号的偏差，利用偏差信号对受控对象进行控制，以减小或纠正输出量的偏差。
Moreover, this algorithm is carries on under the closed-loop system, it can examine the component signal deviation that controls the object to reduce or correct output error.
高轮廓的音盆环绕设备采用丁基橡胶以允许更大偏差，因而产生更大输出。
The tall profile cone surrounds are of butyl rubber to allow greater excursion, and therefore higher output.
高轮廓的音盆环绕设备采用丁基橡胶以允许更大偏差，因而产生更大输出。
The tall profile cone surrounds are of butyl rubber to allow greater excursion, and therefore higher output.
应用推荐