简单的方法来设置轴的位置在熊猫吗？
另一造成不同的原因,就是旋转的轴的位置。
And what also makes the difference about which axis you rotate the object.
以实现输入信号成比例的输出轴的位置控制。
And realize the proportional input signal of the output shaft's position control.
提供30度的调整，使该信号输出轴的位置。
Provides 30 degrees of adjustment to align the signal outputs to the shaft position.
可测量台阶高度，槽宽，在二维方向确定孔或轴的位置。
Measure the height of STeps, width of grooves, position of bores or shafts in 2 co-ordinates.
另一方面，如果所需的速度变化要求某种类型，轴的位置也会被修复。
On the other hand, if a required speed change demands a certain type, the shaft positions will also be fixed.
对于快装式机械密封在整体组装完毕后一定不要忘记将定位片径向移动道远离轴的位置固定。
For fast-loading mechanical seals in the overall assembly must not forget that after the film will be mobile Road radial position away from the fixed axis.
第118行将该值乘以y轴的比例因子，以确定其位置。
Line 118 multiplies it by the Y-axis scaling factor to determine its position.
也要注意时间轴上的迭代的位置与图2中的那些相对应。
Also note that the positions of iterations on the timeline correspond to those in Figure 2.
将人类放在地球活动的中心位置这一做法很典范地代表了地质学家看待人类观念的改变——不再是地球长长的时间轴上微小的一点。
Putting humans at the centre of our planet's activity represents a paradigm shift in the way geologists usually think of our species – as a mere blip on the long timescale of Earth.
旋转的参数是由特定轴上鼠标位置确定的。
The parameter for the rotation is determined from the mouse for the particular axis.
结果如图2 所示。注意gnuplot自动给出了轴的刻度，但是如果需要标注图形的位置，就可以对其进行控制。
The result is shown in Figure 2. Note that gnuplot automatically scales the axes, but you're given control over this if you need to position the plot.
内置的合金线路将在x,y,z轴上定位输入笔的位置。
The built-in alloy wires localize a stylus on the x, y, and z axis points.
下面我将要给各位展示的-,不再是时间在x轴的,离散情况-,我要展示的是,任意时刻上,物体所在的位置。
Now I will give you not only the positions-- as I did here on the x axis - at discrete moments in time-- but I'm going to tell you exactly where the object is at any moment in time.
基于此模型对一种典型六轴工业机器人运动轨迹的位置偏差和姿态偏差进行了测量。
Based on this model, the path position deviation and path orientation deviation of an industrial robot are measured.
NetSearchExtender支持缩写的XPath位置-步骤语法，允许使用子轴（/）和属性轴（@）。
Net Search Extender supports the abbreviated XPath location-step syntax and allows for the use of the child axis (/) and the attribute axis (@).
快怠速凸轮的位置是由阻风门轴上的杆臂控制的。
The fast - idle CAM position is controlled by an arm on the choke shaft.
现在你尽可能平稳地把板倾斜到大约和俯仰轴呈45度角的位置上。
Now you tilt the board as smoothly as possible to about 45 degrees in direction of the pitch axis.
一个轴具有-1和1之间的值。中间位置为0。这种情况用于操纵杆输入和键盘输入。
An axis has a value between -1 and 1. The neutral position is 0. This is the case for joystick input and keyboard input.
它的小信封使太小接受的标准编码器的理想选择位置和速度控制的机制文书轴。
Its small envelope makes it ideal for instrument axes for position and speed control in mechanisms too small to accept standard encoders.
通过改变位置的港口的时间轴，射击秩序和相对的时间可以调整。
By changing the location of the ports in the timing shaft, the firing order and relative timing can be adjusted.
用于将板材固定在X和y轴位置上(支撑架中点与尾部止点上的线对齐)板材尾部顶住木头尾部止点。
Locates the tail of the board in the X and Y position (centre of the stringer aligns with the line on the tail stop). The tail of the board butts up with the wooden tail stop.
在冷热两种状念下进行了轴系合理校中计算，并确定中间轴临时支承的位置、法兰间偏移与曲折值各安装工艺参数。
Rational aligning calculation of propulsion shafting in cold and warm conditions, and confirm several fitting technics parameters include of temporary supports, sags and gaps between flanges.
主轴调质措置的首要位置是轴承位、密封位及轴头和叶轮位。
Spindle quenched renew prime location bearing position, sealing position and the spindle head and impeller position.
该多周期扰动力矩与转台三轴转速有关，影响转台的定位精度、位置精度和速率精度。
The multi-period disturbance torque is related to three-axis rotate speed of turntable and influences localization precision, position precision and speed precision of turntable.
在近距离空中支援的势态下，飞行员能够确定敌人的位置并进行离轴瞄准，然后转身接近并投放武器，这样就可以使暴露给地面的威胁最小化。
In a close air support situation, the pilot can locate and off-boresight target the enemy, come around and release weapons, and thus minimize exposure to ground threats.
科学家发现，食物摆放的最佳方位是在顺时针偏右3.2度的位置，也就是在盘子垂直轴稍稍偏右。
The perfect orientation, the scientists discovered, is for food to point at 3.2 degrees clockwise, a tiny fraction to the right of the vertical axis of the plate.
可手动自动调节控制器主、从轴的相位或相对位置。
Manual and automatic facilities to adjust the phase or relative position between Master and Slave.
可手动自动调节控制器主、从轴的相位或相对位置。
Manual and automatic facilities to adjust the phase or relative position between Master and Slave.
应用推荐