本公司设计的XHJP系列顶轴油系统适用于新建机组配套及在用机组顶轴油系统改造。
Our XHJP series jack pump system applies to new unit and restructure of current jack pump system.
同时随着新上机组容量的增大，转子的重量也随之加大，对顶轴油系统的要求也越来越高。
As the volume of newly operated unit increases, rotor's weight increases as well and has higher requirement for jack pump system.
为了解决这些问题，我公司设计出了一套新型的汽轮机顶轴油供油系统，并以集成式方式(带机架)供货。
In order to solve these problems, we design a new steam turbine jack pump oil supply system and supply in integrated form (with rack).
艉轴管滑油系统的投油清洗。
当轴旋转的时候就把油溅入轴承。
在轴上开出沟槽或装上油环，借离心力将沿轴表面外流的油甩掉，集结后流回油池，因而起到密封的作用。
Out in the shaft loaded oil ring groove or by centrifugal force along the axis of the oil drain off the surface, the oil flows back to the assembly after the pool, and thus play a role in sealing.
文中利用该装置研究了轴针式喷嘴的喷油过程，探讨了喷嘴油束形成的特征。
The apparatus has been used in investigating the spray formation of a pintle nozzle.
动力启动方轴传动装置。销法兰。无油密封垫圈。
Power take - off, squared shaft drive. two stud flange without oil seal gasket.
径向柱塞泵配油轴与转子配合间隙直接影响着泵的性能和寿命。
The clearance between oil distribution axle and rotor of radial piston pump can directly influence the performance and life of pump.
研制出防止轴头甩油的离心密封和螺旋密封组合的新结构。
A new construction which combines centrifugal seal and screw seal has been developed.
弹簧为低应力、油回火、螺旋缠绕在整体钢轴上扭力型弹簧。
Springs shall be low-stress, oil tempered, helical wound, torsion type on continuous shaft, Solid CRS or tubular as required.
介绍了具有油束撞击效应的轴针式喷油器在不同柴油机燃烧系统中的应用。
This paper reports experimental results of the mixture formed by Pintle nozzle with impinging head used to diesel engines with different combustion systems.
为了排除离心力的影响，开发了一种特殊类型的油雾供应机构，安装在轴系统的牵引轴上。
In order to suppress the influence of the centrifugal force, a special type of oil-mist supply mechanism was also developed and installed to the draw-bar shaft of the spindle system.
轮毂接合的长度不应包括O型环、轮毂或轴或悬垂安装轮毂中的油分配槽。
The length of hub engagement shall not include O-ring and oil distribution grooves in the hub or the shaft or the amount of installed hub overhang.
数个油道形成在构成内燃机的阀驱动系统的一部分的摇臂轴的轴体中。
A plurality of oil passages are formed in a shaft body of a rocker shaft, which partially constitutes a valve drive system of an internal combustion engine.
多种法兰，油口，输出轴等连接形式。
A variety of connection types of flange; Rabbet:, output shaft and oil port.
锥齿轮和曲柄轴都在油室内，除定期检查外，无需专门关注。
The bevel gears and the crank shafts are totally enclosed in oil chamber and require no attention, except periodical checks.
多种法兰，输出轴，油口等连接形式。
A variety of connection types of flange; Rabbet:, output shaft and oil port.
如果遇到一扇难开的门，他就会在门轴上涂一点油。
If he faced a door hard to open, he would smear some oil on the hinges.
如果遇到一扇难开的门，他就会在门轴上涂一点油。
If he faced a door hard to open, he would smear some oil on the hinges.
应用推荐