通过对转子发生轴向位移的轴承位置的调整，解除了故障，恢复了正常生产。
By adjusting the position of bearings for axial displacement of rotor, the faults were discharged, and the normal production was recovered.
通常，偏差不超过1,5角分钟，从他们的中心位置，不产生负面影响单列圆锥滚子轴承的功能。
Misalignments not exceeding 1, 5 angular minutes from their centre position, usually, do not negatively affect the function of single row taper roller bearings.
主轴调质措置的首要位置是轴承位、密封位及轴头和叶轮位。
Spindle quenched renew prime location bearing position, sealing position and the spindle head and impeller position.
轴向偏移以及对中误差会影响CAR B轴承中的滚子轴向位置。
Misalignment as well as axial displacement influences the axial positions of the rollers in a CARB bearing.
这座桥由弹性轴承支撑，并在移动过程中由一个定心元素将它带到中间适当的位置之上。
The bridge is supported by elastomeric bearings and is brought into the correct position by a centering element in the middle in the process of movement.
主要研究一种无传感器磁轴承转子位置自检测的方法，该方法不需要专用的位移传感器。
A method of automatically detecting rotor position of self-sensing magnetic bearing is studied, in this method, no special displacement sensors are used.
由于轴承结构原因，沟道位置难以测量。
Because of the bearing structure, measuring racew ay position is difficult.
传感器最佳位置是在曲轴轴承正对的发动机两侧或油底壳处。
The optimal positions of the vibration sensor should be located on both sides of the crank-shaft bearing or bottom of the engine.
合理地布置平衡重的位置以使主轴承载荷的最大值达到最小，这是平衡重设计的又一问题。
The reasonable disposition of the crankshaft counterweight can minimize the maximum load on the main bearing, it is another problem of the design of the counterweight.
在叉头套加工过程中，轴承孔位置误差的测量和控制是十分重要。
It is very important to measure and control the position of bearing hole when machining canular forked shaft.
这种类型的轴承一般使用在邻近位置。
滑动轴承油膜破裂位置是滑动轴承静特性之一。
Oil film fracture position is an important characteristic of journal bearing.
为了实现磁力轴承系统中转子的位置控制，需要建立一个闭环的位置反馈控制系统。
In order to realize rotor position control in the magnetic bearing system, a closed loop position feedback control system is needed to be established.
在内端盖与机座的连接 处法兰上铣一个与轴承盖上所铣平面位置相对的槽，槽内放置测速传感器；将 轴头压板改为齿盘结构。
A groove is milled on the flange for installing the speed sensor at the junction of the inner end cap and the seat, which is facing to the plane on the bearing cap.
对造成轧辊烧轴承的原因进行了分析，结果表明：轧辊烧轴承主要与轧辊送进角的变化，冷却水的水量、水压及水管位置，轧辊架变形情况等有关。
Result showed that main reasons on ablation of roll bearing were transformation of forward Angle, flow value of cool water, water pressure, water pipe position, and deformation of roll-shell et al.
压头在压紧轴承的时候，可以自动调整压头的位置，保证各压头压力均等。
When the squeeze heads compress the bearing, the position of the squeeze heads can be automatically adjusted to guarantee each squeeze head pressure is equal.
因此，可测量该轴承的所需位置的温度。
As a result, the temperature of a desired position of the bearing can be measured.
传动轴在止推轴承处带有千分尺调节器，以使壳内叶轮处于中心位置。
The shaft is provided with a micrometer adjustment at the thrust bearing to permit proper centering of impeller in casing.
因此选择泵的安装位置时，要使泵盖和轴承座的热量便于扩散，不出现任何蓄热现象。
Therefore, when selecting the installation position of the pump, the heat quantity of the pump cover and the bearing seat is easy to spread, and no heat accumulation phenomenon occurs.
在电磁轴承系统中，位置测量误差直接影响着系统性能。
The performances of EMB system are directly affected by position measurement error.
用于手轮执行器阀门上的地轴承架可以在上方对阀门进行操作，包括手轮，暗杆，连接件，加长件，以及带闸板位置指示器的地轴承架。
A floorstand for handwheel actuated valves allows operation from above. Included is handwheel, non-rising stem, fittings, extension, and floorstand with gate position indicator.
该系统运用目前新技术，解决了以往存在的轴承存储位置不准确与选配轴承时匹配精度不高的问题。
It USES the present newly technology, to solve the problems that the storage locations of bearings are not accurate and the matching accuracy is not high.
轴承座分 别将两根执行丝杆及位置传动丝杆固定在底座上；
By bearing seat two executing screw shafts and position driving screw shafts are set on the base plate.
轴承径向和轴向的承载能力都比较大，各配件可替换性强。轴承通过调节偏心外六角来调整芯轴位置进而达到调整侧滚轮轴向尺寸的目的。
With greater axial and radial load rating capacity, good replaceability of components. The shaft can be adjusted through external hexogan then to adjust the axial part dimension.
从而，可达到加工简易及可大量生产，还可稳固轴心位置，使在轴承中的轴心保持在中央的位置上。
Thereby, the easy processing and mass production are realized, and the position of the axial center can also be stable for holding the axial center of the bearing on the central position.
同样装好同一根轴上的另一端轴承和座，将轴转动几圈，让轴承本身自动找正位置后。
Also installed on the same shaft to the other side of the bearing and seat, will turn a few laps, let shaft bearing itself automatically find the position is.
在轴承与主轴支撑面的径向位置上设有的热膨胀量和弹性变形余地。
The radial position between the bearing and the supporting surface of the main axis is provided with a space for the heat inflation and the springy transformation.
轴承零件在正常相对位置时，滚动体与滚道表面接触的点。
Bearing parts in the normal relative position, the surface of the rolling element and raceway contact points.
计算结果表明，几何形状误差和位置误差对该种轴承的静态特性有着不同程度的影响。
The calculation results show that the geometric form error and the bearing alignment error affect the static characteristics of the bearing in different degrees.
计算结果表明，几何形状误差和位置误差对该种轴承的静态特性有着不同程度的影响。
The calculation results show that the geometric form error and the bearing alignment error affect the static characteristics of the bearing in different degrees.
应用推荐