因此，外侧车轮转速要快于内侧车轮。
As a result, the outside wheel turns faster than the inside wheel.
快速转换锯轮转速装置。
只有当离合器盘和飞轮转速不同的时候，离合器才会磨损。
The clutch only wears while the clutch disc and the flywheel are spinning at different speeds.
在冷端条件一定的情况下，提高砂轮转速能降低砂轮外圆面温度。
The results show that higher heat flux causes higher temperature on external circular surface of the grinding wheel.
对锑化铟-铟共晶薄膜磁阻元件的齿轮转速传感器电路进行了研究。
The gear velocity sensor made up of a InSn-In eutectic film magnetoresistor(MR) is studied.
研究了砂轮转速、进给量等工艺参数对石英玻璃表面粗糙度的影响；
The technological parameters such as electrolysis current, the rotation speed of grinding wheel and the feed rate etc, have been optimized.
数值计算结果表明：齿轮传动的接触疲劳寿命与齿轮转速戚息相关。
The numerical results show that the gear contact fatigue life is connected with gear rotational velocity.
所以，探讨齿轮转速对齿轮传动接触疲劳寿命影响是必要且可行的。
Therefore, it is necessary and feasible to explore the effect of gear rotational speed on the gear contact fatigue life.
经风洞标定试验，改造后的风速表叶轮转速与风速有良好的线性关系。
Through wind standard tunnel test, linear relationship is found out between the impeller speed and the air speed of refitted air speedometer.
本文指出如何减少牙轮转速的差别及对牙轮钻头合金齿提出具体要求。
In this paper, some Suggestions of how to minimize the difference of rotation speeds and the requirements for the c...
本文指出如何减少牙轮转速的差别及对牙轮钻头合金齿提出具体要求。
In this paper, some Suggestions of how to minimize the difference of rotation speeds and the requirements for...
本文指出如何减少牙轮转速的差别及对牙轮钻头合金齿提出具体要求。
In this paper, some Suggestions of how to minimize the difference of rotation speeds and th...
此程序为风速仪的测试程序，包括风速的测定及风轮转速的显示等功能。
This procedure anemometer testing procedures, including the determination of wind speed and wind wheel speed display.
增加砂轮转速、砂轮摆动和轴向进给量可以提高单晶金刚石的研磨效率。
The increase of the wheel speed, the swing frequency and the feed of shaft direction conduce to improving the grinding efficiency.
介绍一种利用光学方法检测涡轮转速的光纤涡轮流量传感器及检测系统。
The optical fiber turbine flow sensor and detecting system, in which the rotational speed of the turbine is measured with optical technique, are presented.
为给自由涡轮转速装置的定检提供参考，设计了微型自由涡轮转速测试仪。
In order to offer reference for periodic check of free turbine, the minitype Rev testing meter of free turbine was designed.
反馈线性化控制器用于保持涡轮转速与用户自定义的辅助输入量的线性关系。
The feedback linearization controller ensures that a linear relationship is maintained between the turbine speed and an additional user defined input.
方法考察压轮压力、压轮转速和浸膏粉含水量对颗粒得率和颗粒脆碎度的影响。
Methods The influence of roller pressure, roller speed, and water content of extract powder on yield and friability of particle diameter was investigated.
对三轴稳定地球同步卫星中用于姿态控制的偏置动量轮转速变化问题进行研究。
This paper researches the variation of the Momentum Wheel(MW) rotation rate which is applied to attitude control in three-axis stabilized GEO satellites.
方法：考察轧轮压力、轧轮转速和浸膏粉含水量对颗粒得率和颗粒脆碎度的影响。
Method: Inspect the influence of roller press, roller speed and the water content of extract powder on yield and friability of particle diameter.
研究表明：分级粒径的大小与涡轮转速、抽风机风量、风压及涡轮结构参数有关。
The study shows that the separation size is related to the rotary velocity of the turbo, the wind volume and the wind pressure of the exhaust fan, the structure and parameters of the turbo.
结果：轧轮压力、轧轮转速和浸膏粉含水量对颗粒得率和颗粒脆碎度有显著性影响。
Result: the roller press, roller speed and the water content of extract powder had a significant degree of influence.
通过改变砂轮转速、砂轮摆动频率、轴向进给量，获得了一些具有对比性的试验结果。
By changing the speed of grinding wheel, its swing frequency and the feed speed of shaft direction, different experiment results were got.
重点阐释了风力发电机变桨矩控制方法对风力发电机组的功率流动、叶轮转速变化的影响。
The influence of control method for pitch on power flowing and rotating speed of the vane are focused.
发现一个牙轮钻头中的三个牙轮回转速度不相同。而不同类型牙轮钻头的牙轮转速也不相同。
It was found that the rotation speeds of 3 cones in one rotary bit are different, and the speeds of rotation are also different for different types of rock bits.
分析了九杯静电高速自动喷涂机设备出现的故障和蜗轮转速、漆流量等问题，给出了解决办法。
Common failure, turbine rotating speeding, paint flow rate and etc. of nine-cup electrostatic hing-speed automatic spraying equipment are analyzed. Solving method is given.
分析了九杯静电高速自动喷涂机设备出现的故障和蜗轮转速、漆流量等问题，给出了解决办法。
Common failure, turbine rotating speeding, paint flow rate and etc. of nine-cup electrostatic hing-speed automatic spraying equipment are analyzed. Solving method is given.
应用推荐