随着计算机技术的飞速发展，精馏过程的模型化与仿真已成为化工工艺设计和操作分析的主要工具。
With the development of computer technology, the modeling and simulation of rectifying process already become the mainly tools on chemical technological design and operation.
针对冲压机械的特点，采用计算机仿真和物理模拟，为冲压类机械动态特性分析与研究提供了一种实用方法。
According to the features of the punch machine, we research on the dynamic properties and put forward a practical way by means of computer simulation and physical simulation.
为确定自激电容值与异步发电机空载建压时间的关系，对建压暂态过程进行了仿真计算和分析。
The relationship between the excitation capacitance and the voltage-buildup time in an induction generator was analyzed using a transient simulation and analysis.
利用计算机建模与仿真的方法，对电动节流阀控制系统正常和异常时电机电压和阀门转角的波动进行了分析。
By means of computered modeling and simulating, the variation of the discrepancy of motor voltage and valve Angle are analyzed when system working at proper or fault condition.
在对军用飞机维修保障过程分析的基础上，运用离散事件建模方法和计算机建模与仿真技术建立了飞机维修保障仿真模型。
An aviation maintenance model is established by using the discrete event modeling method and computer modeling and simulation technique after analyzing the military airplane maintenance process.
分析和仿真计算结果表明，与传统的等比特分配方法相比，该动态比特分配算法可以显著地改善系统性能。
Compared with the conventional equal bit allocation method, the DBA method can improve the system performance greatly by analysis and numerical simulation.
建立了图像采集系统分析模型，计算机仿真分析图像采集系统端到端信息率与采样目标统计特性的关系。
The analysis model of image gathering system is proposed. The relationship of system end-to-end information rate with target statistical characteristics is examined by computer simulation.
经计算机仿真与理论分析表明，该算法与传统恒模算法相比，收敛速度加快，稳态剩余误差减小。
Computer simulations and theory analyses show that the proposed algorithm can speed up convergence rate and decrease state residual error compared with conventional CMA blind equalization algorithm.
根据研究所得的宽展规律，采用有限元分析与解析计算相结合的方法，建立了适合宝钢2050粗轧区带钢宽展计算的快速仿真模型。
Based on the spread rule obtained, a fast simulation spread model for 2050 hot strip roughing trains at Baosteel has been established by combining the finite element analysis and analytical model.
理论分析和计算机仿真实验均表明该算法与传统的恒模算法相比，都具有更快的收敛速度和更小的稳态剩余误差。
Theoritical analyse and computer simulation both shows the new one has faster convergent speed and less steady error than traditional constant-modulus algorithms.
为了充分发挥电网实时数据在日常分析计算中的作用，简化数据录入工作，开发了EMS系统与仿真软件的在线数据接口软件。
In order to make full use of grid real-time data in daily analysis and calculation and simplify the data entry, the online interface software of EMS and PSASP is developed.
理论分析和计算机仿真实验均表明，新算法与传统的恒模算法相比，具有更快的收敛速度和更小的稳态剩余误差。
The theoretical analysis and the simulation results proved to show that the new algorithm has improved performance of the convergence speed and residual error than traditional CM algorithm.
本文将直流偏磁现象与电磁场计算有机地结合在一起，对变压器在不同直流偏磁下的运行性能做了仿真和分析。
The phenomenon of DC magnetic bias analysis and electromagnetic field calculating are combined in this paper and the running performance is simulated with different magnetic bias DC.
本文建立了硅片自旋转磨削的运动几何学模型，分析了磨削参数与磨削纹理的关系，并对磨粒磨削运动轨迹进行了计算机仿真和预测；
The relationship between grinding marks and the grinding parameters is analyzed. The cutting trajectories of grits on the wafer are predicted by computer simulation.
通过理论分析，提出一个经校正的输出解耦阵，并经计算机仿真分析与实验验证表明，此解耦阵完全可以实现实时性很好的计算机全解耦。
The theoretical analysis and the computer simulation show that the whole decoupling of DTG can fully be realized with a high real-time capability.
本文基于矢量传感器阵组合增益的理论分析，在不同方位给出了各种矢量阵组合增益的计算机仿真结果，理论分析与仿真结果吻合很好。
Based on the theoretical analysis of vector array combined gain, the simulation results of different bearings are given, which are in accord with the theoretical analysis.
用计算机仿真的方法在数字用户环路上实现了该算法，并测定其数字用户环路上所能获得的最大传码率，分析最大传码率与发送总功率的关系，给出比特分配结果。
On the digital subscriber loop we realized the algorithm, got the max receiving bit, analysed the relation between the max receiving bit and transmitted power, and got the result of bit allocation.
对于连续与离散积分型变结构控制，分别从理论分析计算与数值仿真两种途径得到了典型惯性过程的参数可摄动范围。
The perturbation domains of parameters in typical inertial process are obtained by theoretical analysis and numerical simulation respectively for continuous and discrete integral VSC.
实例计算入端阻抗与实测的结果吻合得很好，表明该模型可以用于变压器冲击试验的故障仿真分析。
The comparison between the calculated impedance and the measured impedance has shown that the proposed model can be used to simulate the impulse voltage test with sufficient precision.
通过仿真分析可知与阵元域高分辨定位方法相比，该方法计算简单，运算量小，而且算法性能更好。
Through analysis we know that compared with array region high resolution, this method has simpler and less amount of calculation as well as better algorithm performance.
提出了工业建设项目风险分析计算机仿真的一般原理与方法，并对仿真结果进行了精度分析。
The general principle and method of computer simulation for the risk analysis of the constructive project of industry are presented. The accuracy of the Simulation result is analyzed as well.
该文通过对R-D成像方法的分析，推导了在R-D成像方法下雷达工作频率，信号带宽与成像角之间的关系，并用计算机仿真进行了验证。
With the analysis of R-D algorithm, the relationship between the frequency of radar, the signal frequency width and the squint angle is deduced. The result is identified by computer simulation.
并按照该理论与方法，从计算机实现的角度提出了可行的步骤与方案。利用此方案建立的凸轮实体精度高，并可进行有限元分析和加工仿真。
And on the base of the theory, in the view of the computer realization, the reliable steps and method are provided, its merits and disadvantages are summarized.
文中给出了两口井的计算机仿真试验与实粘结果分析比较图，从而验证了建模方法及仿真计算的正确性。
The comparison diagram of computer simulation test and field practice between 2 Wells were shown, which testified the accuracy of the method and simulation calculation.
研究了磁阻效应的扭矩信号处理方法，分析了信号相位差的相关分析法和频谱分析法，并进行了仿真计算与误差分析。
The real-time shaft power is being monitored by calculating the torsional Angle and shaft speed on line. 2 the torsion signal processing method is researched on.
研究了磁阻效应的扭矩信号处理方法，分析了信号相位差的相关分析法和频谱分析法，并进行了仿真计算与误差分析。
The real-time shaft power is being monitored by calculating the torsional Angle and shaft speed on line. 2 the torsion signal processing method is researched on.
应用推荐