在钻机里常采用弧齿圆锥齿轮提高角传动齿轮承载能力。
Spiral bevel gears are usually used to improve the bearing capacity of the Angle transmission gears on drill RIGS.
大的角传动比意味着，对于给定的车轮转角，其转向盘转过的角度更大。
A higher ratio means that you have to turn the steering wheel more to get the wheels to turn a given distance.
利用解析方法对转向机构进行了运动分析，导出了运动关系式及角传动比计算式。
In this paper the steering gear kinematics is studied, the kinetic relationship and angular transmission ratio equations are derived.
本文介绍了PC—1500计算机测试系统的硬件、软件和在转向器角传动比测试中的应用。
In this paper, the hardware and software of the PC-1500 computer measurement system as well as its application for measuring Angle drive ratio of steering wheel are introduced.
有些车的转向系角传动比是可变的，这种转向器采用齿轮齿条式，它在中间而不是外部，有不同的齿密度（每寸齿数）。
Some cars have variable-ratio steering, which uses a rack-and-pinion gear set that has a different tooth pitch (number of teeth per inch) in the center than it has on the outside.
对于相啮齿轮端面齿廓相互关系的分析表明，目前使用的几种基准齿形，当螺旋角传动比都比较大时，存在齿形干涉的危险。
Then, it is indicated that the gearing used presently, while its helix Angle and ratio are both big enough, is in danger of interference.
传动系角传动比低，则转向灵敏- - - - - -当你想将车轮转过一定角度时，不必把转向盘转很大的角度- - - - - -正是赛车所需要的。
The lower ratio gives the steering a quicker response — you don't have to turn the steering wheel as much to get the wheels to turn a given distance — which is a desirable trait in sports cars.
利用摆动活齿传动等效机构，分析其传动性能和最小传动角的位置。
According to its equivalent mechanism-crank rocker mechanism, driving performance and minimum driving Angle position of movable tooth is analyzed.
首先分析了转向机构中最小传动角对汽车转向横拉杆作用力的影响。
Firstly, forces on steering tie-rod are analyzed when minimum driving Angle of steering mechanism is changed.
本文讨论在己知最小传动角条件下设计曲柄摇杆机构的方法。
This paper discusses the method for designing of crank rocker mechanism under given minimum transmission Angle conditions.
前端轮系从手动张紧的三角带传动改为自动张紧的多楔带传动，运转更平稳，可靠性高。
Front-wheel system was changed from the manual tension V-belt to automatic tension V-ribbed belts , more smoother operation and higher reliability.
本文提出了一种利用计算机计算齿轮传动啮合角的简便易行的方法。
This paper presents a practical method to calculate the pressure angle at pitch cylinder, of gear drive with computer.
测量结果就是传动轴工作角(c)。
This measurement will give you the propeller shaft Angle (C).
通过运动学的分析，确定了机器的驱动装置——气缸中活塞的行程，并保证了机构的最小传动角符合要求；
The driving unit of machine—the distance of piston is ascertained with kinematics analysis and the smallest transmission angle is conformable.
提供了一种少齿数齿轮传动系统输出运动误差和回程误差角的计算方法。
A kind of calculation method for outputting motion error and return stroke error Angle of less toothed gear drive system was provided.
本文介绍了糖果裹包机的具有最佳传动角的曲柄摇杆机构的设计，采用微机控制，给出了硬件和软件程序框。
The paper introduces the designs of best transmission angle of crank sliding block mechanism for candy packaging machine controled by computer.
由一对两级三角皮带轮传动工件主轴，使其获得四级转速；
The work spindle get four-grade rotate speed, which is driven by a couple of two-grade v-belt pulley.
在大多数的使用情况下，四杆曲线同源机构与原始机构具有相同的传动角。
In many cases, transmission angles of cognate mechanism and original mechanism are identical.
该种组合机构结构较简单，容易设计，传动角大。
This kind of combination mechanism is rather simple in structure, easy to design and of a big transmission Angle.
特点：双辊破碎机采用三角带或万向节联轴器进行传动和调节两辊之间的间隙。
Features: double rollers crusher adopts v-belts or gimbal couplings for transmission and adjust the gap between two roller.
阐述了确定行程速比系数和的平面曲柄摇杆机构最小传动角位置和大小的新方法。
According to its equivalent mechanism-crank rocker mechanism, driving performance and minimum driving Angle position of movable tooth is analyzed.
根据四杆机构的杆长关系，具体给出了最小传动角的准确位置。
According to relationship between the length of the linking rods of the four link mechanism, the paper proposes an accurate location of the minimum transmission Angle.
本程序适用于一个装有多个传动部件，且各传动部件上受载点方位角又不相同的轴系上之轴承组合设计计算。
A program is suitable, for the calculation in designing bearing combinations of a shaft system with transmission components which are loaded in different directions.
本文分析偏置双曲柄滑块机构的急回运动特性，给出了按最小传动角设计偏置双曲柄滑块机构的设计方法和设计曲线。
The characteristic of quick-return of offset double crank slider mechanism was analyzed in this paper. The synthesis method and curve of this mechanism with minimum transmission angle were presented.
在加工允许的范围内，螺旋角取较大的数值，能够较好地改善啮合性能，从而发挥二次包络TI蜗杆传动的优势。
Within the range of machining, if the helix Angle adopts a bigger value, it may improve the meshing performance and develop the advantages of double enveloping TI worm gearing.
然后详细的讨论了五杆机构在每一种分类情况下机构中存在双曲柄时机构的传动比及相位角的范围。
Then we conclude the five-bar's classification and the gear ratio and phase Angle in each classification to be full rotatability.
该优化方法的处理，对解决正角变位传动行星轮系的优化问题，有一定价值。
This method has some value in solving the problem of option of the planet gear wheel system of positive Angle change position drive.
然后，针对能够整周转动的齿轮—五杆机构，研究了其上的一点在齿轮机构的传动比、初始相位角、杆长以及两杆之间的夹角变化时的轨迹曲线以及速度和加速度曲线的情况。
Then the locus curves of one point in the geared five-bar were studied with the change of the gear ratio, the phase Angle, the bar length and the Angle between two bars.
转向万向节的精度，特别是加载过程中转向传动轴产生的角间隙直接影响汽车转向系统的灵敏度。
The accuracy of universal joints of steering shafts, especially angular clearance of steering shafts under loading conditions, will directly influence the sensitivity of automotive steering systems.
转向万向节的精度，特别是加载过程中转向传动轴产生的角间隙直接影响汽车转向系统的灵敏度。
The accuracy of universal joints of steering shafts, especially angular clearance of steering shafts under loading conditions, will directly influence the sensitivity of automotive steering systems.
应用推荐