铝基复合材料内螺纹攻丝属封闭切削，加工难度大，丝锥极易折断。
It is very difficult to tap inside Aluminum matrix composites. The process is difficult to operate due to its close condition, and the tap is subject to breaking.
公司有各种吨位的压机119台，此外还有各类剪板机、储能焊机、自动机械手设备及螺纹攻丝、滚丝设备以及数台数控机床、加工中心等。
We possess about 119 Presses of different tonnages, Cutting Machines, Multi Spot Welding Machines and Welding Robot Systems, Tapping Machines, Thread Rolling Machines, CNC and others.
介绍一种新型手用工具的工作原理及设计方法。该工具运用了一种新型棘轮换向机构，可提高手工攻丝或拆装螺纹工件的工作效率。
The operating principle and design method of a new manual tool are introduced. An intermittent revolution mechanism is applied to the tool to improve screwing efficiency.
冲击攻丝作为一种新型的内螺纹加工技术，在解决小直径薄板内螺纹加工方面发挥着重要的作用，并具有良好的应用前景。
Impact tapping, as a novel technology of internal thread processing, has some important effect and a good applied foreground in the machining of small diameter thread, especially for thin board.
导电件螺纹孔采用无切削攻丝新工艺，解决了已往导电件螺纹容易滑牙的缺陷。
Conductive thread of a hole without cutting tapping new technology to solve the past conductive thread easily slip teeth of the defects.
理论上同意，操作者可以在致密刀柄上使用攻丝螺纹。
This theoretical agreement leads with the user to the acceptance that thread taps can be used in rigid tool holder without problems.
攻丝是在一个孔中车出螺纹，以便装上有帽螺钉或螺栓。
Tapping is the process of cutting a thread inside a hole so that a cap screw or bolt may be threaded into it.
这些方法对减小攻丝扭矩、提高内螺纹质量、改善攻丝效果、促进振动攻丝的实际应用具有一定理论和实践意义。
These ways are valuable to decrease the torque of vibratory tapping, improve the quality of tapping and promote the practise use of vibratory tapping.
具有车、铣、镗、钻四大自动化功能，可车削球面、柱面、锥面、螺纹、攻丝、端面、内外环槽等。
With cars, milling, boring, drilling four automation function, can be turning sphere, cylinder, cone, thread, tapping, end face, inner and outer ring groove, etc.
前言：钢质曲轴螺孔攻丝加工中经常出现螺纹烂牙、中径扩大等问题，且刀具寿命较短。
During tapping in steel crankshafts, the most commonly encountered problems are "mess tooth" and oversize thread, additionally the tap life is very low.
此外，他们认为，对于攻丝存在一个临界切削厚度(螺纹深度)值，在临界切削厚度的范围内，攻丝能降低攻丝扭矩。
In addition, they believe, for tapping there exists a critical cutting thickness (thread depth) value of the critical cutting thickness within the tapping can reduce the tapping torque.
攻丝是切削加工中广泛使用的一种内螺纹加工方法。
采用振动挤压攻丝新方法对钛合金材料进行内螺纹加工，螺纹表面硬度高，丝锥损坏现象显著减小。
Adopting the new method to female thread machining, high hardness of thread can be acquired, and tap broken cases reduce significantly.
在加工中小直径内螺纹和在难加工材料上攻丝时，普遍存在攻丝扭矩大、螺纹精度低、丝锥易折断、废品率高等问题，而采用低频振动攻丝是解决此问题行之有效的方法。
When tapping the little diameter in the material of difficult processing, there usually exist a lot of questions such as tapping torsion heavy, thread accuracy low, rejecting rate high.
第一端盖（6）的孔（14）被攻丝以容纳完全互补的带螺 纹连接件（5），所述带螺纹连接件（5）接着连接到丙烷气体汽缸。
The bore (14) of the first end cap (6) is threaded to accommodate a complementary threaded connector (5) which, in turn, is connected to a cylinder of propane gas.
冲击攻丝作为一种新型的内螺纹加工技术，在解决小直径薄板内螺纹加工方面发挥着重要的作用，并具有良好的应用前景。
Theoretic analysis indicates that the impact effect and stress waves of tap on the workpiece result in extended micro cracks, leading to lower plastic deformation and a much lower tapping torque.
冲击攻丝作为一种新型的内螺纹加工技术，在解决小直径薄板内螺纹加工方面发挥着重要的作用，并具有良好的应用前景。
Theoretic analysis indicates that the impact effect and stress waves of tap on the workpiece result in extended micro cracks, leading to lower plastic deformation and a much lower tapping torque.
应用推荐