轮子旋转时需要承受巨大的和不断变化的压力，所以要使结构更坚固，钢的部分要用螺栓连接，而不是焊接在一起。
The wheel would need to withstand immense and constantly changing stresses as it rotated, so to make the structure more robust, the steel sections were bolted rather than welded together.
我用螺栓和螺帽焊接雕塑，你能在很多城市看到那些雕塑屹立在那儿。
混凝土墙、钢梁和张量组成结构，用自身美学标识立面，在工业和现代的建筑外观上表现螺栓和焊接的结构。
Concrete walls, steel beams and tensors compose the structure that marks the facade with its own aesthetics, showing the bolts and welding on an industrial and contemporary look.
有地下室工程的塔吊基础还要采取特别的处理措施：如在基础下打桩，并将桩端的钢筋与基础地脚螺栓牢固的焊接在一起。
A tower crane foundation basement project should take measures in particular: such as piling in foundation, and pile reinforcement and foundation anchor bolts end firmly welded together.
操作机器或设备，焊接，螺栓，螺钉或铆钉金属零件。
Operate machines or equipment which weld, solder, bolt, screw or rivet metal parts together.
用于焊接螺母磁场传感器检测，不仅金属但它也取代了位置螺栓。
The magnetic field sensor for weld nuts detects not only metal but it also replaces the location bolt.
使用联接器，夹子，螺钉，螺栓，水泥或焊接，钎焊和焊接设备连接管件。
Join pipes using couplings, clamps, screws, bolts, cement or soldering, brazing and welding equipment.
在前不久的一次参观中，球屋里充斥着各种噪音，在这个正在建设中的建筑里，工人们在焊接钢筋，打入螺栓，切割混凝土。
There was plenty of noise inside the spheres on a recent tour, as workers welded steel, pounded bolts into place and sawed concrete inside the half-built structure.
将转接件分别焊接在埋件上及工字钢上，然后将立柱用螺栓与转接件连接起来。
Weld switchover pieces separately on embedment and I-steel, and then connect the mullion with bolts and switchover pieces.
根据安装图(或吊点图)的要求，将销座组件用螺栓或焊接方式固定在指定的生根梁上。
Pursuant to requirements in installation diagram (or points hanging diagram), pin boss components are fastened to the appointed rooting beam by bolts or in a welding way.
螺栓与螺母不配。我们认为焊接比铆接好。
钢柱通过螺栓与埋板连接，校准后进行焊接。
Steel columns are connected via bolts and cast-in plate and will be welded after calibration.
本文在大量实验的基础上提出了对焊接节点采用断裂力学的方法和对螺栓球节点应用累积损伤理论估算它们疲劳寿命的计算方法。
Finally, the methods for calculating fatigue life based on fracture mechanics for welded node and cumulative damage theory for bolted sphere node respectively have been presented.
将概率分级筛激振器机架的结构由整体焊接式改为螺栓联接式，使用方便，效果很好。
The structure of probability screen vibration frame change unitary welded type to bolt fastening. This way USES handy and effect is well.
海行射钉紧固技术与传统的预埋固定，打洞浇注，螺栓连接及焊接等方法相比，具有许多优越性。
Compared with the traditional methods, such as embedded fixation, hole casting, bolt connection and welding, Haihang nail fastening technology has many advantages.
三跨的人行桥的桥面为钢结构，总共三段，每段分开焊接制作，通过螺栓连接。
The steel-structure bridge deck is three-span, and each one is welded separately with bolt connection.
提出了螺栓焊的新机理和螺栓设计原则。 设计了电磁开关壳体螺栓焊的焊接模具；
This paper propose the new mechanism of bolt welding, and the design of clamping yokes for hilt welding of electromagnetic switch shell.
这类鞍形管卡的优点是可对管道泄漏点进行永久性修理，把钢板和管子焊接，然后拆走螺栓部分。
An advantage of this type of saddle clamp was that permanent repair could be made by welding the steel piece to the pipe and then removing the bolted portions.
碳钢，合金钢或不锈钢，压力密封或螺栓阀帽用于焊接在螺栓阀帽阀门上阀座的设备。
Carbon, Alloy or Stainless Steel, Pressure seal or Bolted Bonnet Provision for seal Welding on Bolted Bonnet Valves.
屈服钢板墙约束板端部先焊接厚钢板，再用高强螺栓连接的方式较为合理可靠；
The connection mode that the end of steel plate shear wall is firstly welded onto a piece of steel plate, then connected by high-strength bolt is reasonable and reliable;
机座在大多数情况下是焊接结构，用螺栓固定在构成船舶双层底的底座上。
The bedplate, which in most cases is of the welded design, is bolted to the seating which Forms a part of double of the ship.
你不需要任何螺栓连接，螺纹连接，或焊接现场。
第五、在地面用膨胀螺栓固定后焊接钢筋做假山的龙骨，然后把钢丝网绑上，再抹灰，然后待其百分之60干度时根据造型刮好。
The fifth, on the ground with expansion bolts fixed welded steel rockeries and keel, then the tie wire, plaster, and the percent of 60 stem degrees according to shape a good scratch.
由于采用螺栓联接，避免了焊接质量差的水下焊接，可直接用于海底管道维修。
Poor sub-sea welding is avoided by using bolt connection; it can be directly used for sub-sea pipeline welding.
第二、在地面用膨胀螺栓固定后焊接钢筋做假山的龙骨，然后把钢丝网绑上，再抹灰，然后待其百分之60干度时根据造型刮好。
Second, on the ground made the rockery after expansion bolt welded steel keel, and then tied the wire mesh, plaster, then treat its sixty percent dryness according to sweep.
他说，一点点加工需要做的阴极管，螺纹螺栓作出枢纽这是焊接管通过一个惰性气体保护焊机，氩弧焊或。
He says a little machining needs to be done on the cathode tube, making a threaded bolt hub that is welded to the tube via an inert gas shield welder, or tig.
套筒与新旧螺栓之间采用对角焊接。
The opposite Angle welding is adopted between the sleeve, the new bolt and the old bolt.
套筒与新旧螺栓之间采用对角焊接。
The opposite Angle welding is adopted between the sleeve, the new bolt and the old bolt.
应用推荐