it管理者所需要的材料，都列在这里-螺丝，螺帽，啤酒盖，内存，处理器，光碟之类的东西！
All the things necessary for an IT administrator are here - screws, nuts, "beer", "memory", "processors", discs and stuff like that!
打开绞丝盖后，我们现在取下绞丝下面用来固定的螺丝。
With the hinge cover removed, we now remove the screw right under the hinge.
在LCD的左右两侧有两个绞丝盖。它们用来隐藏和保护内部的螺丝。
There are two hinge cover on the left and right side of the LCD. It hides and protects the screws n stuff.
拆卸一个灯头钉头螺丝，三个套筒头螺栓和齿轮执行机构盖。
Remove one socket pin head screw, three socket head bolts and gear operator cover.
注：如果出现少量的泄漏，则拆卸锁紧螺丝，然后锁住垫圈和阀盖，然后轻轻紧固填料压紧螺母。
NOTE: If minor leakage occurs, remove lock screw, lock washer and cap and lightly tighten packing gland nut.
拆卸一个灯头钉头螺丝(C)，三个套筒头螺栓(d)和齿轮执行机构盖(E)。
Remove one socket pin head screw (c), three socket head bolts (d) and gear operator cover (e).
手表的底盖用精密螺丝固定，保证在水深50米下仍具有良好的防水功能。
Watch precision screw fixed case back to ensure that at depths of 50 meters under the water still has a good feature.
用一根清洁杆或同等物，打开末端盖去检查螺丝。
Using a trim stick or equivalent, open the end covers to access the screws.
你曾听说过机油盖或泄油螺丝没栓紧的事吗？
整机外壳采用不锈钢盖型螺母，更有效保护螺丝长时间户外及化工的恶略环境不受损伤，使拆卸维护更加方便。
The stainless steel cap nuts on shell of the hoist protect the screw from various injuries of exposed outdoor for long time and severe chemical environment.
采用大小适中的扳手，松开止回阀盖。旋下止回阀盖螺丝并拿起。
Using an appropriate sized wrench, loosen the check valve cover. Unscrew the check valve cover and lift off.
维修组件饱含：1件-柔性密封衬垫阀座，1件-铰柱，2件-阀瓣板，2件-阀瓣盖，1件-柱带，2件-阀座柱O形环和塑料总成螺丝。
Repair Kit Contains: 1-Flex Seal Gasket Seat, 1-Hinge Post, 2-Flapper Plates, 2-Flapper Covers, 1-Post Strip, 2-Seat Post O-Rings &Plastic Assembly Screws.
用一把小螺丝刀将旧的缓冲垫向上从导槽和盖锁上部的锁止片中撬出。
Use a small screwdriver to prise the old buffer up out of the guide and out of the locking lugs on the upper part of the lid lock.
拆去连接末端端盖前面到部分板下侧的螺丝。
Install the bolts attaching the end cap to the front fender.
魔方故障是指魔方在比赛中发生的故障，如：飞棱、魔板线断裂，螺丝钉、中心盖、贴纸等脱落；
Puzzle defects are defects of puzzles, like: pieces popping, wires breaking, screws/caps/stickers falling off.
拆去连接末端端盖前面到部分板下侧的螺丝。
Pull back the wheelhouse liner and remove the bolts attaching the end cap to the front fender.
拆去连接末端端盖前面到部分板下侧的螺丝。
Pull back the wheelhouse liner and remove the bolts attaching the end cap to the front fender.
应用推荐