因为我使用能显示所有零件、螺丝钉、一切部分安装位置的3dCAD程序。
Because I use a 3d CAD program that shows placement of all parts, screws, everything.
产品有以下缺陷：水冷头上的安装孔没有螺纹，用配带的自攻螺丝安装非常困难。
there has no screw thread on the installation hole on head of water-cooling. It's difficult to install it by the screw tap which along the products.
警告：在安装期间，不要采用任何尖锐的工具，如：撬棍或螺丝刀等。尖锐的工具可能会损伤法兰面，从而可能导致泄露。
CAUTION: Do not use any sharp tools such as a crowbar or screwdriver on the rubber during installation. Sharp instruments can damage the flange face and cause possible leakage.
当安装散热器，收紧螺丝或者，一个又一个的时间。
When installing the cooler, tighten both screws alternatively, one turn at a time.
在安装前应注意各部的螺丝受力是否平衡、升降(活动)是否灵活。
Departments should pay attention to before installing the screw force is balanced, lifting (activity) it is flexible.
安装把视镜固定在车门上的螺丝。
在拧管道接头螺丝时，应遵循对角互拧的原则，不要逐个顺序进行操作，不要一次性将螺丝拧死，这样才能将橡胶垫片正确地安装上去。
When the pipe joint screw, should follow the principle of diagonal twist, not one by one in order to operate, do not screw the screw die, so that the correct installation of rubber gasket.
工业连接器的锁定，只需要一个简单的螺丝要安装驱动程序。
The latching industrial connector requires only a simple screw driver to install.
立柱在同一水平线后，高速护栏板的安装也就非常容易、便捷了，否则会出现螺丝错位的现象，无法安装。
Column in the same horizontal line, the high speed rail board installation is very easy, convenient, otherwise there will be a phenomenon of screw dislocation, can not be installed.
抗粗暴使用的钉入式梅花螺丝用于加固合叶、门挡、门插销和门栓，以及安装五金件。
Vandal-resistant, Pin-in-Head Torx Screws attach hinges, door stops, door latch keepers and mounting hardware.
液压站在安装前应首先作地基平整处理，并打好地脚螺丝的预埋坑。
Prior to installation of the hydraulic station, firstly level the foundation, and dig the embedded pits for the foundation bolts.
在离照明灯最近而又通风散热良好的地方，通过使用双面胶布、扎带、螺丝等材料将镇流器牢固安装固定。
Stick the ballast on the nearest place from the headlamp in the engine room firmly by using double-faced tape cable tie and etc.
配置防盗不锈钢梅花螺丝钉锁孔，便于门五金件和所有安装支架的安装。
Theft-resistant, stainless steel pin-in-head Torx screws are furnished for door hardware and all mounting brackets.
将烘干后的细河沙放在柴油机旁，以便放入地脚螺丝安装孔内。
Put the dried river fine sand beside the diesel engine, so as to be conveniently filled into the foundation screw mounting holes.
此外维修工具、螺丝等以防掉落，对于沿街、道路上空的空调安装，应特别注意其安全性。
In addition, repair tools, screws, etc. to prevent falling, for the street, the road over the air conditioning installation, special attention should be their safety.
将面板底面避开LED位置钻孔用螺丝固定再安装壁面上，按设计之板安装好，并将每个字的线头固定好。
Second, the bottom panel of the surface to avoid led drilling hole position is fixed by the screw to install wall on, installed according to the design of plate and fixed thread on each word.
安装负荷细胞，是实现由一个单一的螺栓，其中螺丝钉成为一个挖孔在该基地的负载细胞。
Mounting of the load cell is achieved by a single bolt which screws into a tapped hole at the base of the load cell.
电容器外壳的材质采用优质冷轧钢板或不锈钢板，两侧装有供吊运安装支架，并装有专用的接地螺丝。
Capacitor shell adopts the high quality cold-rolled steel sheet or stainless steel sheet, and with mounting bracket for lifting on both sides which equipped with special grounding screw.
螺丝盖子已经在管筒的顶部安装到位，管筒的下端开口以便于填装过程。
The screw cap is already in place at the top of the tube and the lower end is open for the filling procedure.
涂胶固定螺丝的使用很少。磁铁座上安装振动膜的螺丝是涂胶固定的。
Fixed screw painted with glue is barely used. The screw for mounting diaphragm on the magnet base is fixed by glue.
安装螺丝的扭力，请严格遵守目录所标示的扭力。
Lock the mounting bolts according to the torque marked in the catalogue.
灯具螺丝安装孔的螺纹能够保证安全地安装和拆除。
Threads intended to receive holding installation and removal of knurled headed screws.
安装把视镜固定在车门上的螺丝。
再次扭转安装螺丝的换向电子阀，跟随手册中的扭力值转开。
Retorque pilot valve mounting screws, following the torque values in this manual.
接着向后移动所述外壳，并通过拧紧所述罩安装螺丝来将所述外壳锁定在适当的位置。
The housing is then moved rearwardly and locked in place by tightening the hood mounting screws.
L301型粘度计有一个1/4”NPT的螺丝配合一个T型的管道，可以很容易的安装到管线上，或者用一个焊接套环，安装到大罐子或管道内。
The Model SPC/L301 viscometer has a 1 1/4" NPT thread to easily install into a process line using a "Tee", or into a large tank or pipe, using a weld ferrule.
原有平头十字螺丝改为平头内六角螺丝。以增强安装或拆卸止水栓时的力度需求。
Flat-head inner hexagon screws instead the flat-heat cross-screw to increase the required installation and disassembly force.
本实用新型与螺丝刀配合使用，拆卸安装螺丝钉方便，具有很好的推广价值。
The utility model can be matched with screwdrivers, and the assembly and disassembly of the screws is convenient.
本实用新型与螺丝刀配合使用，拆卸安装螺丝钉方便，具有很好的推广价值。
The utility model can be matched with screwdrivers, and the assembly and disassembly of the screws is convenient.
应用推荐