将蒸汽注入以防止在铁水的制造中氧气和烃气互相接触。
The vapor is injected to prevent the oxygen and the hydrocarbon gas from contacting each other in the manufacturing of molten iron.
室内实验表明，伴蒸汽注入化学剂是提高稠油油藏采收率的有效手段。
The laboratory experiment presents that chemical agent injection with steam is the effective means for improving recovery factor of heavy oil reservoir.
在蒸汽驱和蒸汽吞吐过程中，影响蒸汽注入剖面的主要因素是蒸汽超复现象和高渗透层。
Major factors which influence the steam injection profile are steam overlaying and high-permeability zones during steam flooding and cyclic steam injection.
由于汽缸中注入了冷水，蒸汽迅速凝结了。
The steam was condensed rapidly by injecting cold water into the cylinder.
在相邻的井注入水或蒸汽以帮助压出石油。
Water or steam may be pumped down adjacent wells to help push the oil out.
在新的工程中最常用的技术，则是往地下的沥青中注入蒸汽。
The most common technique in new projects involves injecting the bitumen with steam underground.
在注入热量和注汽时间相同情况下，先注高干度蒸汽可提高开发速度和经济效益。
In the case of same injected heat and steam injected time, high steam quality can improve development rate and economical benefit.
如何确定注入蒸汽的井底状态，从而准确地预测其产量的变化是成功与否的关键。
How to make sure of the injected steam's situation at bottom of well is the key for accurately predicting output variety.
在特斯拉涡轮机，空气，蒸汽，油，或任何其他流体被注入一个光滑的平行磁盘系列边缘。
In the Tesla Turbine, air, steam, oil, or any other fluid is injected at the edge of a series of smooth parallel disks.
鉴于其不能对未来进行预测，提出了应用注采曲线法同hcz模型相结合对现场注入蒸汽及稠油产量进行预测的方法。
Because it can not predict the future index, this paper combine the injection-production-curve method with HCZ model, find the method of predicting steam injection and heavy oil production.
芳香是向咖啡中注入热水、搅动湿咖啡粉而释放蒸汽时散发的咖啡味道。
Aroma is the smell of the coffee when it is infused with hot water and vapors are released as the wet coffee grounds are stirred.
蒸汽清洁器水槽中只能注入干净的自来水或蒸馏水。
Only put clean tap or distilled water in your Steam Cleaner tank.
电位法井间测试是一种新型、有效的应用于油藏动态监测的技术之一，它能够准确地测定注入介质(蒸汽或水)的推进方位及波及范围。
Interwell testing by electric potential is a new, effective reservoir dynamic monitoring technique. It can accurately test the advancing direction and swept region of injected media (steam or water).
利用金属蒸汽真空弧（MEVVA）源所产生的强束流离子注入铝研究了相变、增强扩散和钇铝合金的形成条件。
Phase transition, enhanced diffusion and Y-Al alloy formation are studied using Y implantation with high current extracted from metal vapor vacuum arc (MEVVA) ion source.
方法针对胜利油区稠油开发中出现的注入蒸汽的窜进和生产井水窜的问题，研究适用于热采井封堵汽窜和水窜的HBC981热采封堵剂。
Method To eliminate steam coning and water coning in production Wells of heavy oil reservoirs, Shengli oil province, HBC98 1 plugging agent for thermal production is developed.
注蒸汽稠油热采是指稠油开采时向稠油层注入适当干度的高压蒸汽进行原油采集。
Steam thermal drive oil is the method in which high pressure steam with suitable dryness fraction is injected into heavy oil stratum.
在注入蒸汽开采初始条件下，能量效率可以达到7.0。
Under the production condition of steam injection, the energy ratio can reach 7.0.
解决方案为加入降凝剂，并在罐上部注入蒸汽。
The solutions are adding the pour point depression agent and steam injection from the top.
蒸汽吞吐热力采油的效果取决于由注采参数决定的注入蒸汽的热能利用程度。
The level of oil production using steam injection technique directly depends on the heat efficiency of steam injection, and the heat efficiency can be determined by injection-production parameters.
向产层注入热水、热蒸汽或热气体，以降低油的粘度，并将油经储层压向生产井。
Hot water, steam, or gas is injected into the producing formation to lower the viscosity of the oil and force it through the reservoir toward producing Wells.
模拟研究表明，在吞吐后期宜采取先注氮气、后注蒸汽的注入方式，并且存在一个优化的周期注氮量。
The results from reservoir simulation indicated that it is reasonable to inject nitrogen first and then steam at late steam soaking, and there exists an optimum nitrogen volume in a injection cycle.
注汽开采中高温高压蒸汽的频繁注入又加剧了地层出砂，这些状况极大地限制了稠油的有效开采。
In steam injection production, the steam with HTHP can stimulate formation sand production. These statuses restrict the output of heavy oil.
蒸汽驱的注入参数对蒸汽驱驱油效果影响非常大。
Steam injection parameters design is very important, which extremely affects success of steam flooding.
为了获得蒸汽驱油藏最大采收率和最佳经济效果，必须对蒸汽驱注入参数进行优选。
In order to achieve maximum recovery rate and the optimum economic results, steam injection parameters must be optimized.
为了获得蒸汽驱油藏最大采收率和最佳经济效果，必须对蒸汽驱注入参数进行优选。
In order to achieve maximum recovery rate and the optimum economic results, steam injection parameters must be optimized.
应用推荐