对熔覆层显微组织形貌、硬度分布进行了分析研究。
Study on microstructure and performance of Fe-base alloy coating produced by plasma cladding;
利用透射电子显微镜分析了合金在不同条件下的组织形貌特征。
The microstructure characteristics of the alloy after different deformations were analyzed.
另外，第二火70%的大变形量对网篮组织形貌的变化影响不大。
Moreover, great deformation amount to 70% didn't change the basketweave.
贝氏体在转变机理上、动力学上、组织形貌上都存在明显的过渡性。
There is visible transitionary character in microstructure and morphology, transformation mechanism, and transformation dynamics.
通过对以上合金组织形貌的观察，分析了压力对合金凝固过程的影响。
By observing the microstructure of the alloy, the effect of pressure were analysed.
并对合成的基本原理和形成自修复陶瓷层的组织形貌进行了分析研究。
And the basic principal has synthesized and the self-repair pottery surface appearance was discussed.
用XRD和SEM分析了铸态及快淬态合金的相结构及微观组织形貌。
The phase structure and microstructure morphologies of the as-cast and quenched alloys were analysed and observed by XRD and SEM.
利用场发射电镜、能谱仪等对接合区的界面和组织形貌进行了分析比较。
The microforms of diffusion joint were analyzed using field emission scanning electron microscope with an attached energy dispersive Xray analyzer.
对涂层的组织形貌和相组成进行分析，并研究了实验工艺对涂层结构的影响。
The effects of experiment parameters on the phase constitution and the structure morphologies of the coating was studied.
系统地研究了溅射功率对沉积速率、薄膜结构、组织形貌及接触性能的影响。
The influences of the sputtering power on deposition rate, film structure, and contact performance of the film prepared on CdZnTe substrate have been investigated.
用扫描和高压透射电子显微镜研究了灰铸铁激光硬化层微区组织形貌和精细结构。
Micromorphology and fine structure in laser hardened layer of grey cast iron have been investigated with scanning electron microscope and high-voltage transmission electron microscope.
考察了复合材料的组织形貌和复合材料的形成过程，以及模温和转速对组织的影响。
The formation mechanism of the gradient was discussed. The effect of technological parameters on the composites was investigated.
纳米氧化铈颗粒改变了锌涂层的表面组织形貌和晶体结构，从而提高了涂层的耐蚀性。
Ceria nanoparticles modify the surface morphology and crystal structure of the zinc matrix in correlation with the increase of corrosion resistance.
观察到高应变率时应力平台与硬化阶段的TEM组织形貌分别为孪晶与断续的马氏体。
TEM morphology of the twin specimens at stress plateau stage and martensite section at hardening stage has been observed.
用XRD和SEM分析了铸态及快淬态合金的相结构，并观察了合金的微观组织形貌。
The phase structure and microstructure of as-cast and quenched alloys were analyzed and observed by XRD and SEM.
分析了三种铬系白口铸铁的碳化物类型、制备工艺、组织形貌、性能特点以及应用范围。
The carbides types, techniques preparation, microstructure, property, and applications range of three kinds of chromium white cast iron were introduced.
考察了复合材料的组织形貌，检测了复合材料的硬度和耐磨性，分析了复合材料的断裂模式。
The structure morphology the hardness and wear resistance of composite have been investigated, and fracture model of the composites has been analyzed.
焊核区由于动态再结晶具有细小的等轴晶粒，旁边存在一个特殊的组织形貌——热机影响区域。
The fine grain and narrow HAZ were found in friction stir weld and the dynamic recrystallization produces fine grain.
随着变形量的增加，组织形貌发生显著变化，钼颗粒沿轴向被拉长，粘结相铜也被拉成长条状；
First, Mo-Cu or Mo-Mo binder interface separation was happened, then molybdenum particle began to rupture.
绘制了氧化动力学曲线，用带能谱分析的扫描电镜观察了涂层的表面氧化形貌和横截面组织形貌。
The oxidation kinetics curve was drawn. The surface morphology and cross section micrograph of the Al-Si coating were studied by using SEM.
采用着色腐蚀技术，金相显示了球墨铸铁缩松区中奥氏体枝晶组织形貌，分析了球铁缩松的形成机制。
The morphology of austenite dendrites in shrinkage porosity in nodular iron is displayed by the color etching technique and the formation mechanism of shrinkage porosity has been analyzed.
分析了涂覆界面附近区域的显微组织形貌、相结构及化学成分，并对显微硬度和耐蚀性进行了测试。
The microstructure, phase structure and composition of the area near the coating interface were analyzed. The microhardness and corrosion resistance of the coating were also tested.
利用光学显微镜（OM）和透射电子显微镜（TEM）观察合金不同热变形条件下的组织形貌特征。
The microstructure features at different hot deformation conditions were analyzed with optical microscope (OM) and transmission electron microscope (TEM).
研究了硫酸盐镍电镀液的组成及浓度，特别是糖精添加剂含量对电铸镍沉积层组织形貌和性能的影响。
The influence of the content of saccharin additive in sulphate bath on the microstructure and properties of Nickel deposit made by electric casting was investigated.
通过进行蠕变曲线测定和组织形貌观察，研究了FGH95粉末镍基合金的微观组织结构与蠕变行为。
By means of the measurement of creep curves and microstructure observation, an investigation has been made into the microstructure and creep behaviors of FGH95 powder nickel-base superalloy.
研究了在非稳态条件下，搅拌铸造工艺参数对ZA27合金的凝固过程及初生相组织形貌转变的影响。
The effects of casting process parameters on transformational behavior of primary nondendrite phase and solidification process of ZA27 alloy in stirring are investigated under transient condition.
结果表明，钛合金活性焊剂对焊接接头的宏观组织形貌有明显影响，但对焊接接头的化学组成没有影响。
The results showed that the activating flux has a visible influence on the crystal structure of welds, but has no relationship with the composition of the welds.
研究了稀土元素对AZ 91 D压铸镁合金高周疲劳性能的影响，并对疲劳断口的组织形貌进行了分析。
Influence of rare earth elements on high-cycle fatigue properties of AZ91D alloy was investigated and the fatigue fracture morphology was also analyzed.
展示了30层连续熔敷后的组织形貌，说明组织和硬度都比较均匀，并介绍了若干激光修复工业应用实例。
The microstructure of 30-layered laser cladded coating was displayed. It had uniform microstructure and hardness. Several examples of its industrial application were also carried out.
展示了30层连续熔敷后的组织形貌，说明组织和硬度都比较均匀，并介绍了若干激光修复工业应用实例。
The microstructure of 30-layered laser cladded coating was displayed. It had uniform microstructure and hardness. Several examples of its industrial application were also carried out.
应用推荐