然后仪表通过同一套测试引线来测量电阻两端的电压，并计算出相应的电阻数值。
The meter then measures the voltage across the resistance through the same set of test leads and computes the resistance value accordingly.
此电阻器则将增益限制到一个有限的数值。
The resistor limits this increase in gain to a finite value.
由于机械振动引起导电材料的微粒移动，可能会大大改变电阻的数值。
Mechanical shock may significantly alter the resistance by dislodging particles of the conductive material.
数值模拟是研究电阻点焊过程和机理的重要手段。
Numerical simulation is an important method for investigating of resistance spot welding process.
测量的粒子，表面电阻和膜厚度的数值分别记录在表单，见表2。
The measured value of particle, sheet resistance and film thickness have been respectively recorded in a table, please see table2.
根据GIS的结构特点，对一种带有并联电阻的隔离开关抑制VFTO的机理、作用进行了数值分析。
Base on the structural characteristic of GIS, the mechanism and effects of disconnector with shunt resistor to depress VFTO are simulated and analyzed in this paper.
从前置处理、数值计算及后置处理三个方面出发，着重介绍可视化技术在电阻点焊过程数值分析软件中的应用。
Based on the pre-process, numerical simulation and post-process, the application of visualization technique, which is used in the numerical analysis of resistance spot welding process, is introduced.
本文在大电机定子空心导体分层的基础上，推导了导体交流电阻的数值计算公式。
On the basis of stator hollow conductor layer building in large electric machines, the paper deduces numerical formula for calculating conductor alternating current resistance.
本文研究了用有限元数值方法模拟柯尔—柯尔复电阻率模型异常规律的问题。
In this paper, we discuss the numerical modeling of complex resistivity anomalies for Cole-Cole dispersion model by the Finite Element Method (FEM).
给出了一种时间域瞬变电磁法视电阻率的数值计算方法，利用该方法可以容易地求出中心方式的全程视电阻率。
A numerical method for calculating the exact all-time apparent resistivity for time domain transient electromagnetic method is proposed in this paper.
在大数值电阻和电容的情况下，上升时间可能达到数分钟。
In the case of large resistors and capacitance, the rise time can range up to minutes.
采用数值计算方法分析了垂直接地极对接地系统的接地电阻、接触电压及跨步电压等的影响。
The influences of vertical grounding electrodes on grounding resistance, step and touch voltages were analyzed numerically.
采用数值方法，分析了不同生物传热模型条件下，采用热敏电阻探头加热时，生物组织中温度响应的动态特征。
The tissue temperature responses generated from heating by a spherical thermistor probe were calculated by using a numerical method, in which different bio-heat transfer models were adopted.
通过对电阻率测深数据作数值差分处理，使区域场受到压制而局部场得到突出，并且多个相互叠加的异常也得到分离，有利于解释推断。
To process data of resistivity sounding by numeric difference method will separate all anomalies and it will be beneficial to interpretation and inference.
采用试验和有限元数值模拟的方法，对汽车车身低碳钢电阻点焊的过程进行了研究。
The resistance spot welding process of mild steel was studied by experimental and finite element methods.
利用数值模拟方法研究了罐底土壤电阻率沿垂直方向变化对电位分布的影响。
The effect of soil resistivity change along vertical direction on potential distribution was studied through numerical simulation.
给出了一种方便快捷的瞬变电磁全区视电阻率数值计算方法逆样条插值法。
Aimed at central loop array, a method calculating the all-time apparent resistivity is proposed, .
本文用有限单元法对坑道内的直流电阻率测深进行数值模拟计算。
In this paper, we performed modelling of DC resistivity sounding in tunnel using the finite element method (FEM).
应用一种新型的数值模式匹配(nmm)理论快速完成了普通电阻率测井的数值模拟。
A new type of numerical mode-matching (NMM) theory is applied into numerical simulation of common resistivity logs.
以数值结果揭示外延层的体电阻率及厚度、活性区载流子的扩散长度、模增益和丝区宽度等参量对上述各种分布的影响。
Numerical results indicate how the various parameters such as bulk resistivity and carrier diffusion length in the active region affect the profiles.
采用有限元素法进行三维数值模拟研究微电阻率成像测井响应。
FEM (Finite Element Method) is used for 3d numerical simulation to study micro resistivity imaging logging responses.
一些电开盖装有二极管或电阻器铸件，这些是不可忽略的，必须用数值检测运行的正确。
Some solenoid caps have a diode or resistor cast into the cap to prevent feedback on the R terminal. These shall not be eliminated. The values must be tested for correct operation.
测量外界采集卡a端口的数值并将其转化为电阻阻值。
Measure a port capture card volume outside values and translate them into resistor.
干燥土壤，如墙上的泥土，其电阻较大，在仪表上显示的数值就较高。
Dry soils (such as those over walls) are more resistant to electricity and give higher readings on the meter.
利用有限单元法对水下电阻率测深进行数值模拟。
The paper discusses resistivity sounding modeling under water using FEM.
用数值模拟和反演成像方法对实测电位数据进行了处理，得到了2 6J9井区目的层的电阻率和剩余油饱和度分布。
The data in the area of the borehole of 8-26-J9 were obtained with the borehole-to-surface electrical measurement method.
用数值模拟和反演成像方法对实测电位数据进行了处理，得到了2 6J9井区目的层的电阻率和剩余油饱和度分布。
The data in the area of the borehole of 8-26-J9 were obtained with the borehole-to-surface electrical measurement method.
应用推荐