介绍了绕线式异步电动机起动控制电路改进的情况。
The improvement on the start control circuit of wound asynchronous motor is introduced.
在进行电路改进时，切断主电源，并确保电源完全切断。
When modifying the circuit, it is required to cut off the main power and make sure that the power is disconnected completely.
通过对载波接收机限幅干扰分析，提出电路改进的办法。
Based on the analysis of carrier receiver limited amplitude interference, provide a way of circuit modification.
本文提出电流继电器控制绕线式异步电动机起动电路改进方法，并对改进电路优劣进行了分析。
A method in the improvement of current relay controls winding asynchronous motor starting circuit is put forward, and the merit, demerit of it are described in the paper.
本文介绍了停油电磁铁应用过程中的一起异常烧坏故障以及故障原因分析和有关的电路改进方法。
This paper introduces a exceptional malfunction about Fuel shut-off solenoid which happened during its working and analyses its causation and reasons out a solution to the problem.
示零器电路改进后的交流电桥，增大了示零器电路的内阻，提高了交流电桥的灵敏度，对任何形式的电容电桥、电感电桥都适用。
The increased internal resistance within an improved zero indicator helps increase the sensitivity of the AC bridge and thus can be available for any type of capacity bridge and induction bridge.
示零器电路改进后的交流电桥，增大了示零器电路的内阻，提高了交流电桥的灵敏度，对任何形式的电容电桥、电感电桥都适用。
The increased internal resistance within an improved zero indicator helps increase the sensitivity of the AC bridge and thus can be...
此次佳能通过改进读取电路的时序控制方法，成功实现了传感器信号的高速读出。
By modifying the method employed to control the readout circuit timing, Canon successfully achieved the high-speed readout of sensor signals.
结合试验过程中遇到的问题，给出了改进的直流衰减法测试电路。
Combined with the problems during the experiment, design a improved testing circuit of Direct Current Attenuation Method.
反激式开关变压器和反馈控制回路设计，以及考虑电磁兼容性对电路的改进，是其关键技术。
The design of flyback switching transformer and feedback control loop and the improvement of the circuit for considering electromagnetic compatibility are the critical technologies.
针对TP801 - A型单板机现存缺陷，提出了一种无需触及任何硬件电路的简单易行的改进方案。
To present shortcoming of TP801-A single board computer, the author pointed out a kind of simple reform project without touching on any hardware circuit.
该系统的应用对改进数字电路课程的教学手段具有一定的现实意义。
The application of the system has a practical significance in improving teaching means of digital electrocircuit course.
改进后的触发器，具有保持、置0、置1、翻转四种功能，是一种很理想的电路。
The improved flip is an ideal circuit with the four function of presetting to 1, presetting to 0, maintaining, turning over.
随着生产工艺的改进，电路的集成度还在不断的提高。
With the development of production technology, the integration of IC is also continuously improved.
研究了在雷达吸波结构中应用电路模拟技术改进其在TE极化平面波入射下的反射特性的方法。
How to apply the circuit analog to radar structural absorbers to improve their reflection characteristics under te polarization plane wave incidence is studied.
本文提出了逻辑法设计时序控制电路的改进方法。
An improvement of logic design approach for time-sequence control circuit is presented.
分析了电接点压力表控制电路的弊端，并提出了改进方案。
The malady of control circuit of contact monometers is analysed and improvement plans are suggested.
可控硅触发电路的改进。
在立体声领域，改进控制电路放置非立体声像。
Improved control circuit places monaural image in a stereo field.
给出了实验结果，并提出了几种改进电路参数的方法。
Here also presents experiment results and prefers several methods to improve circuit's parameters.
本文提出一种线性模拟容差电路故障诊断方法——改进的L_1范数方法。
In this paper, an improved L1-norm method for diagnosing the faults in analog circuit with tolerance is proposed.
介绍了mkc—1型快速充电机存在的问题，提出改进方案和电路原理。
This paper introduces the problem mkc-1 type quick charger existing Improvement ways and circuit principle are put.
该法以电路的改进节点方程为基础，具有建立故障诊断方程容易，所建立的方程具有较低的非线性度及规则的雅可比矩阵的特点。
This method based on modified nodal approach is easy to set up the fault diagnosis equations and has lower degree of nonlinearity and regular Jacobi matrix form.
为了提高功放电路的效率，电路被不断改进。
To improve efficiency of power amplification circuit, circuits is being improved ceaselessly.
介绍静电复印机AC驱动器的维修经验并提出用固态继电器对原电路进行改进的方法。
Introduced the repair-experience of the AC driver of the electrostatic printer and proposed the method to improve the primary circuit with the solid-state armature.
改进原电路系统，进一步完善PLC程序。
Meliorating original circuit system and further improving PLC procedures.
在测量系统方面，改进电路设计、减小外界干扰和误差以提高测量精度。
To improve the measurement precision, the circuit is amended and the disturbing signals and measurement errors are reduced.
因此，我们可以通过对LOD电路的改进，来提高整个DSP芯片的工作性能。
So, in order to improve the speed of DSP, we can use the way that improve the speed of LOD.
方法和结果：首先构思电路原理，然后进入实际设计和改进，最后进入实际测试和结果误差分析。
Methods and Results: Conceiving the theory of this circuit at first, then designing and improving in fact, and testing the circuit and analyzing its errors at last.
本文介结了高空作业车液压卸荷和发动机熄火两种紧急停止电路的改进，讨论了电路的可靠性。
Improvement in emergent stop circuits for hydraulic relief and engine stoppage is introduced in the article, and reliability of the electric circuit is discussed.
应用推荐