实验结果证明，这种新型电流模整流器的工作原理是正确的。
The experiment results show that the working principle is correct.
采用电流模理论和电流模电路设计超宽频带、超高速度模拟开关。
Current mode theory enables design of super wide frequency band, super high speed analog switches by introducing circuit structures and principles.
各种模拟功能的线性和非线性电流模集成电路和系统都是由基本?。
So reader can analysis electronic circuit by trans linear circuits, current mirrors, current conveyers, switched current circuit in common use.
介绍了一种低压电流模带隙电压基准电路，并提出了一种新颖的启动电路结构。
A low voltage current mode bandgap voltage reference circuit with a novel start-up circuit is designed.
该芯片采用电流模控制方式，因此对电源电压的响应和对负载变化的瞬态响应迅速。
The chip is adopted current-mode control, so that either its response to the supply voltage or its transient response to load changes is fast.
设计电流模脉冲宽度调制直流转换器时，人们广泛采用斜坡补偿电路来消除谐波振荡。
In the design of current-mode PWM DC-DC converters, the slope compensation method is widely used to prevent sub-harmonic oscillation.
提出了一种基于电流模的开关电流技术取代基于电压模的开关电容技术实现连续小波变换的方法。
This paper proposed a method for the implementation of continuous wavelet-transform (CWT) using switched-current (si) technology, based on current mode and a substitute of switched-capacitor.
以AOA电流模式多路输出积分器和AOA电流模多路输出比例电路为基础，设计了多功能二阶电流模式滤波器。
Based on a current-mode integrator and proportion circuit multiple outputs by AOA, multifunctional second-order current-mode filter was proposed.
随着SACD的日益普及，同目前流行的电压模高保真功放的性能相比，电流模高保真声频功率放大器将会有美好的发展前景。
As the SACD is increasingly popularized, the current mode power amplifier, compared with the prevalent voltage mode Hi-Fi power amplifier, will have a quick development and bright look in the future.
电流模pwm集成dc - DC变换器设计中，为了防止亚谐波振荡而普遍采用的斜坡补偿，会在占空比较大时严重影响芯片的带载能力。
In the design of current-mode PWM DC-DC converters, the slope compensation method widely used to prevent sub-harmonic oscillation can significantly weaken the load capacity under a high duty cycle.
利用线模电流的小波变换系数进行测距，不仅不受故障电阻的影响，也不受故障起始角的影响。
The location result is not influenced by fault resistance and inception Angle when wavelet transform coefficient of aerial mode current is used in fault location.
从图3- 12可以看出，共模电流(ICM)是从电源线经过电源变压器通过电容耦合(CCOUPLING)而产生的。
As shown in Figure 3-12, common - mode current (ICM) is caused by capacitive coupling (CCOUPLING) from the power line through the power transformer.
可能出现的共模电流(ICM)从电压表的输入低端流到仪器的机箱公共端，经过大地再流到电压源的地。
Any common-mode current (ICM) that may be present flows from the voltmeter input lo to instrument chassis common, through earth ground to voltage source ground.
由三相pwm逆变器产生的共模和差模电压可以在电机驱动中产生足够大的共模和差模电流。
The common and differential mode voltage produced by the PWM inverter can generate large common and differential current in the motor driving system.
利用非速度信息，如：电机的电压、电流及电机本身参数，通过滑模观测器产生控制器所需的速度反馈信息。
The control system utilizes a sliding mode observer for the generation of all controller feedback information by means of non-speed information, such as voltage, current and parameters of motor.
再者，所用的放大器也要考虑在加到输入端的整个共模电压(范围内)输入偏置电流转换保持平滑。
Again, consider using AMPLIFIERs that exhibit a smooth input bias current transition throughout the applied input common-mode voltage.
在电流片两侧的基态速度场与磁场相互平行的位形下，讨论了速度切变对撕裂模不稳定性的影响。
The influence of shear flow along the magnetic field accompanied with a plane current layer on the tearing instability is analyzed.
仿真结果表明，所设计的滑模变控制器使助力电机具有很好的动态性能，系统基本无抖动现象，实现了助力电机输出电流对目标电流的跟踪特性。
The simulation results show this control system has good dynamic property and negligible vibration, and efficiently makes the output current of direct motor trace the intent current.
减小探测光输入功率，选取短波长探测光波长，增加半导体光放大器的腔长和模场限制因子以及大的偏置电流可提高转换光消光比；
Meanwhile extinction ratio of converted signal can be improved with low probe power, short probe wavelength, long cavity length, high confinement factor, and large biased current.
其测试诊断步骤依序为：传导发射测试、辐射辐射测试、共模电流测量和机箱泄漏检查。
The testing processes are testing of conductive transmit and radiant transmit, testing of common-mode current and detecting divulgation in turn.
提出了利用二次模变换计算同杆双回输电线路潜供电流与恢复电压稳态值的方法。
A new method for calculating secondary arc current and recovery voltage on double-circuit transmission lines by twice-model transformation was proposed.
整个系统控制分为电压环控制和电流环滑模控制。
The whole control unit is divided into the voltage loop control and the current loop control.
现在，共模电流(ICM)流过r2，产生了一个电压降。这个电压降与被测的电压相加。
Now, the common-mode current (ICM) flows through R2, developing a voltage drop, which is added to the voltage to be measured.
探索综合利用故障初始电流、电压行波线模分量实现配电线路双端故障测距的新方法。
A new method of fault location for distribution feeders based on the aerial mode component of fault generating current and voltage traveling waves is discussed.
对纵环电流天线，可能存在静电模转换激发和直接激发这两种离子伯恩斯·坦波激发方式共存的情况。
We find that for our toroidal current antenna, there may exist two ways of excitation, i. e. direct excitation and excitation through the electrostatic mode conversion process.
该算法产量低共模电压和电流，在可接受哒PWM输入纹波 和输出哒逆变器，并没有过电压 提问题不要像AZSPWM1。
The algorithm yields low common mode voltage and current, acceptable PWM ripple at the input and output of the inverter, and has no overvoltage problems unlike AZSPWM1.
这些误差来源包括偏置电压、噪声和共模电流以及反向误差。
These error sources include offset voltages, noise and common-mode current, and reversal errors.
对该方案的同步采样试验结果和所开发的基于GPS的电流差动保护装置的动模试验结果进行了介绍和分析。
The sampling test results of the proposed scheme are presented and analyzed. The dynam IC simulation test results for the developed GPS based current differential relay are also introduced.
对该方案的同步采样试验结果和所开发的基于GPS的电流差动保护装置的动模试验结果进行了介绍和分析。
The sampling test results of the proposed scheme are presented and analyzed. The dynam IC simulation test results for the developed GPS based current differential relay are also introduced.
应用推荐