电流浪涌损坏了计算机的磁盘驱动器。
举例说明，如果一个激光器正处于电流过载状态，持续下来可能导致机器损坏。传感器能够探测出异常，在损坏发生之前提醒操作人员进行处理。
For instance, if a laser is experiencing an overcurrent situation that could lead to machine failure, the sensors would detect this so that the situation can be addressed before a failure occurs.
当这种混合用在一个半导体晶体管中，来自半导体管过大的电流将损坏器件。
And when the mixture is used for semiconducting, as in a transistor, the excess current from the conducting nanotubes will short the device.
高压、大电流将会流过电池而使其损坏，或使电池发热、冒烟、变形或燃烧。
High voltage and large current will damage batteries and cause overheat, smoke, deform or burn.
最大电流恒定及截止式电路保护装置，免除故障手机线路板进一步损坏。
Protection devices of maximum current steady and cut-off electric circuit avoid further damage of failure phone circuit board.
电阻器(R)必须足够大，以限制流过二极管的电流，使之不会损坏二极管。
The resistor (r) must be large enough to limit the current through the diodes to prevent damage to the diodes.
为防止损坏开关卡，需验证最大电流和最大电压的乘积没有超过开关卡的功率额定值。
To prevent damage to the switch card, verify that the product of the maximum current and maximum voltage does not exceed the power rating of the switch card.
“最大信号电平”是指能够切换但又不会损坏开关卡的电压、电流和功率的最大值。
"Maximum signal levels" refers to the highest levels of voltage, current, and power that can be switched without damaging the switch card.
这些损坏可以表现为器件的立刻失效，也可能发作在过电流冲击事情后许久才失效，缩短济南发光字的工作寿命。
These damage can be manifested as the immediate failure of the device, may also occur in the over-current shock after a long time to failure, shorten the working life of Ji'nan luminous word.
这种损坏通常由极大的瞬态过电流惹起。
This damage is usually caused by a large transient overcurrent.
如果使用高压，则需要利用限流电阻，以免被测装置击穿后损坏电流开关。
If high voltage is used, current limiting resistors are needed to avoid damage to the current switches in case the device under test breaks down.
对于目前的报警防止LD不受损坏过多的电流。
Over current alarm prevents LD from being damaged by excessive over current.
如果电流变得过高，其损耗的功率可能会损坏样品和低温容器。
If the current becomes too high, the power dissipated may damage the sample and the cryostat.
死区时间选择的不合理会使逆变器件产生过高的浪涌电压和电流甚至损坏。
Unreasonable selection of dead time can make inverting components to produce higher inrush voltage and current and even damaged.
由于环境恶劣及电流过载，造成了电机内部起火烧损了定子线圈和转子过热变形及轴承损坏等情况造成电机无法使用。
The firing inside the motor that caused by bad environment and current overload made the stator coils overburned, overheated rotor deformed and bearing damaged, which led to the motor out of service.
c谐波将引起流过无功(功率因数)补偿电容器的电流显著增加，造成电容器投入运行不久就损坏。
C will cause harmonic flow reactive (power factor) compensation capacitor current increase significantly, resulting capacitor will soon be put into operation in damage.
其次，安稳和均匀的导电功能避免电流密度过大，使底衬过热，出现热点而过早损坏。
Secondly, stable and uniform conductive function to avoid the current density is too large, so that the bottom of the hot, hot spots and premature damage.
当电容器上所施加电压高于额定工作电压时，电容器的漏电流将上升，其电气特性将在短时内劣化直至损坏。
When capacitor is used at higher voltage than the rated voltage, leakage current increases, characteristics drastically deteriorate and damage in a short period may occur as a result.
如电压、插座、电流等不正确的电源电压会损坏电磁炉。
Such as: voltage, sockets, current and so on. Incorrect power supply will be damaged Induction Cooker.
万用表是一种常用的测量仪表，但使用不当，特别是误用电流档去测量电压时很容易烧毁保险甚至损坏万用表。
Mulitimeter is used widely. But in the case of error operation, especially when using electricity to measure voltage , it is damaged easyly.
丰田汽车称，部分晶体管可能在高负荷驾驶时因大量电流产生的热量而受到损坏。
Toyota said certain transistors could be damaged from heat caused by a large current flow during high-load driving due to the defect.
作者提示：请确保电源电流和电压与所选的加速表兼容，以实现最优的性能，避免可能的损坏。
Author's note: Be sure that the power source current and voltage are compatible with the accelerometer you've selected to achieve optimal performance and to avoid possible damage.
下面金属线，携带电力负荷，因此防御闪电，闪电可能切断电流或损坏设备。
Lower wires, which carry the power load, are thereby protected against lightning, which might shut off the current or damage equipment.
最完美的短路保护功能，短路电流为零，允许长期短路而不损坏主机；
Perfect short circuit protection. Current turns to be 0 when short circuit occurs, the charger will not be damaged by long time short circuit.
LED光珠的损坏主要是因为电流过大使芯片内部过热造成的。
LED Light bead damage was mainly due to overheating chip overcurrent caused by the Ambassador.
当被测dut发生短路或其他异常导致电流或电压过高时，钳位电路会将输出电压或电流限制在一个固定值上，以保护器件不被损坏。
Meanwhile, the clamp circuit will limit the output voltage or current at a fixed value when they are abnormal that caused by a DUT short circuit or other fault in order to protect the device.
当被测dut发生短路或其他异常导致电流或电压过高时，钳位电路会将输出电压或电流限制在一个固定值上，以保护器件不被损坏。
Meanwhile, the clamp circuit will limit the output voltage or current at a fixed value when they are abnormal that caused by a DUT short circuit or other fault in order to protect the device.
应用推荐