日本丰田佳美94型轿车安全气囊的触发由电控模块根据碰撞传感器的信号进行控制。
Triggering the safety air bag in Toyota Model 94 Camry car is controlled by electronic-controlled module according to the signal from collision sensor.
根据电控喷油器驱动的要求，设计出一种基于单片机pic18f458的电控喷油器智能驱动模块。
According to the requirements of an electronically controlled injector driving solenoid, an intelligent driving module based on Microcontroller PIC18F458 was introduced in this paper.
其中详细阐述了电控系统的硬件设计如喷醇的驱动电路和软件实现编程的思路和方法，比如转速采集模块编程。
Also this paper gives the detailed information of hardware and software designs, such as the driven circuit of ethanol injector and speed capture software module.
采用多线程技术将监控模块与故障诊断模块溶为一体，实现对电控柴油机的故障诊断。
Combining the fault diagnosis module with the monitoring module by using the multi thread technique, a fault diagnosis system for electronic control diesel engine was achieved.
优化后的MAP处理模块可作用电控标定软件的重要组成部分。
The optimized MAP processing modules can work well as an important part of the calibration system of electronically controlled engines.
电控系统软件采用实时模块化编程，具有编程灵活，移植性和扩展性好的特点。
The software was designed on the basis of real-time and modular principle characterizing good flexibility, transplant convenience and extending possibility.
基于CCP协议通信模块的成功开发为电控发动机标定系统的研发提供了实时、准确的通信保障。
The success in development of communication module based on CCP provides the real and accurate data transmission for the electronically controlled engine calibration system.
详细介绍基于红外传感技术的光电控制开关系统的主要功能模块及设计。
The main function modules and design of photoelectric control switch system based on the infrared electronic transducer technology are introduced in detail.
介绍了SIEMENS逻辑模块LOGO在行车抓斗电控中的运用，并将LOGO控制与直流继电器控制进行了比较。
Application of SIEMENS logic module LOGO on bucket electrical control in overhead crane driving was introduced.
喷油系统软件架构设计方面，详细说明电控单元(ecu)系统软件总架构，包括设计的目的、软件是如何进行总体设计和模块划分的。
The software architecture design of fuel system ECU was defined. The software design includes the purpose of the design, and how the software was designed.
采用了高性能的微控制器MC 68376，运用模块化设计方法，针对工程运用的实际特点，全程按照可靠性设计规范，设计了电控单元的硬件和底层软件。
By using high performance the microcontroller MC68376 according to the modularization method and the reliability design procedure, the hardware and fundamental software of ECU were designed.
详细介绍基于红外传感技术的光电控制开关系统的主要功能模块及设计。
It does not use the "charron ring" but use the photoelectric control system.
气电控制模块安装于司钻房，实现远程刹车控制和刹车压力显示；
System installed on the driller's room, to realize remote braking control and pressure;
论述充放电管理方法的总体思路，介绍无损均衡电路及电压、电流、温度的采样，给出充放电控制电路及MOSFET驱动电路等模块的设计。
The premise and background are introduced. It proposes the overall structure and non-dissipative equalization circuit of charging and discharging management method study.
论述充放电管理方法的总体思路，介绍无损均衡电路及电压、电流、温度的采样，给出充放电控制电路及MOSFET驱动电路等模块的设计。
The premise and background are introduced. It proposes the overall structure and non-dissipative equalization circuit of charging and discharging management method study.
应用推荐