减轻套管损坏就是缩小剪切滑移量。
Mitigating casing damage usually means reducing the amount of shear slip.
预紧力的大小与CFRP筋的滑移量有关。
The prestressing load has something to do with the displacement of CFRP tendon.
泵实际工作过程中，其内部存在泄漏，也称滑移量。
Pump actual work process, their internal leakage there is, also known as slippage.
本文通过用定滑移量法、定负荷法和模拟缝合法对真丝织物的纰裂性能进行测试。
The main idea of this article is by through three methods including fixed-slippage-amount method, fixed-load method and analog method to test the slippage performance of pure silk fabrics.
通过半主动控制后，不但具有较好的隔震效果，而且能有效地减小基底的最大滑移量及残余位移。
The sliding structure with semi-active control shows good isolation effect, and the basic maximum sliding displacement and residual displacement were lesser.
轴压比对节点的抗震性能有利，它可以提高节点的初裂荷载、抗剪承载力、减小节点中梁筋的粘结滑移量。
Axial compressive ratio is advantageous to seismic behavior of staggered joints. It can improve joints first crashing loads, shear resistance capacity and reduce the sliding displacement of beam bars.
为了求解钢筋与混凝土间滑移量，对黏结滑移基本方程进行了分析，导出了黏结应力-局部滑移相互关系的二阶微分方程。
In order to study the slip between rebar and concrete, the fundamental equations are analyzed and the 2nd order differential equation of the relation between bond stress and local slip are obtained.
对计算实例的分析表明，通过半主动控制的滑移隔震结构不但具有较好的隔震效果，且能有效地减小基底的最大滑移量及残余位移。
Numerical results show that the sliding vibration isolation structure using semi-active control not only has good isolation effect, but also has lesser maximum slippage and residual base displacement.
对实例计算结果的分析表明，半主动控制下的滑移隔震结构不但具有较好的隔震效果，而且能有效地减小基底的最大滑移量及残馀位移。
Numerical results show that the sliding structure using semi-active control not only has good vibration isolation effect, but also has less maximum slippage and less residual base displacement.
对于一维碰撞，根据碰撞后车辆的滑移距离和车辆的塑性变形量，反推计算出车辆碰撞后的速度和碰撞前的接触速度；
For collinear collision, the preceding collision velocity and post collision velocity are calculated on the basis of the slippage distance and unreturnable distortion of collision vehicle;
结果表明：单晶连铸铝线材在变形量小于395％时，其塑性变形具有明显的单系滑移特征，当变形量大于395％时，才出现多系滑移特征。
The results indicate that when the plastic strain is smaller than 39 5%, plastic deformation has typicality of uniserial slipping.
结果表明：单晶连铸铝线材在变形量小于395％时，其塑性变形具有明显的单系滑移特征，当变形量大于395％时，才出现多系滑移特征。
The results indicate that when the plastic strain is smaller than 39 5%, plastic deformation has typicality of uniserial slipping.
应用推荐