起居室温度分布看起来更合理。
The living room temperature distributions seem more reasonable.
您的库房做温度分布测试了吗？
在点火器出口处的径向温度分布是均匀的。
The temperature radial distributing are evenly in the outflux of ignition.
可配合分布光纤温度系统，测得温度分布。
With distributing optical temperature system can measure temperature distribution.
炉膛温度分布是否合理，炉膛配风至关重要。
The air distribution is a key to the temperature distribution.
研究了引发剂浓度对前端速度和温度分布的影响。
The effect of the initiator concentration on the speed and temperature profile of frontal polymerization was investigated.
本文就机床主轴箱的瞬态温度分布提供一个近似解。
This paper presents an approximate solution of instantaneous temperature distribution of the headstock.
分析了副槽入口风速等参数对转子温度分布的影响。
The effect of inlet velocity of fluid on temperature distribution was analyzed.
可自动测量热斑的温度分布及寻找热斑的最高温度区域；
The system can automatically measure temperature distribution of thermal spots and looks for the maximum temperature region of a thermal spot.
研究了钢包在各个周转阶段的包衬温度分布及其变化规律。
The temperature distribution and its changing rule of ladle lining at each turnover stage were studied.
指出径向温度分布不均匀是导致输出功率受限的主要原因。
Inhomogeneous distribution of radial temperature is major factor resulted in output power restriction.
箱内设计有合理的热风循环通道，使箱内温度分布更加均匀。
Reasonable hot air circulation channel is designed in the cabinet, so that the temperature distribution in the cabinet is more even.
利用光导纤维测定温度和温度分布，是一项崭新的应用技术。
Temperature measurement by optical fiber is a new applied technology.
本文建立了有限几何尺寸板条激光介质的三维温度分布模型。
In this paper, a three-dimensional model for temperature profile in finite laser slabs is presented.
并利用优化技术调整结构尺寸，使各部件中温度分布趋于均匀。
And optimization technology is used to adjust the ventilation structure dimensions, so that the temperature of each part in the machine can be well distributed.
计算了在光泵期间均匀光泵引起激光棒中温度分布随时间的变化。
Homogeneous pumping induced time dependence of temperature distribution in Bolid state laser rods during pumping is. Calculated.
此模型能够反映出沿炉膛高度方向热流和温度分布随炉内工况变化。
Change of heat flux and temperature distribution along furnace height with varying furnace conditions can be reflected in the model.
论述了该型催化转换器的气体流动特性、温度分布和塑性应变分布。
Discuss the gas flow characteristics, temperature distribution and plastic strain distribution of this catalytic converter part.
从炉子的设计角度提出了解决炉内流动场、温度分布不均匀的方案。
The methods to solve the problems were given from the angle of the furnace design.
本文介绍利用双镜干涉仪测量对流传热边界层中二维温度分布的方法。
By means of a double mirror interferometry a two-dimensional temperature distribution measurement in convective heat boundary layers is presented.
通过对管道流温度分布的分析，得出由温度分布计算管涌流速的公式。
Through the analysis of temperature in piping flow, a piping velocity equation is proposed.
凝析气井井筒温度分布是进行气井节点分析和动态分析必不可少的参数。
The well bore temperature distribution in condensate gas well is indispensable for the node analysis and performance analysis for gas well.
在已知物料特性参数的前提下，能够计算出颗粒料的温度分布和水分分布。
The temperature and moisture distribution can be calculated on the premise of material characteristic parameters.
最初这一地区将会是空白，请注意温度分布的所作所为定性一样，压力分布。
Initially this region will be blank, note that the temperature distribution behaves qualitatively like the pressure distribution.
采用控制容积法对钢—混凝土结合梁试件升温过程的温度分布进行数值计算。
The temperature distribution in temperature rising process of steel-concrete composite beam is calculated by volume-control method.
补燃室内复杂的温度分布和空气与燃气的掺混、燃烧及流动状态有密切关系。
In the afterburner, the complicated temperature distribution has close relation with the dilution, combustion and flow of the air and gas.
利用有限元法对混炼过程中密炼室、胶料的温度分布以及变化情况进行了分析。
Using the finite element method to analyze the mixing chamber, the temperature distribution as well as the change situation.
在此基础上对冷却器效果、电机稳态温度场和空气温度分布进行完整的分析计算。
On this Basis, analysis and calculation of cooler effect, steady temperature field in machine and air temperature distribution have been done.
在二元试验燃烧室上，研究了四种掺混孔设计方案对燃烧室出口径向温度分布影响。
The exit radial temperature profiles formed by four configurations of dilution hole design have been studied experimentally on a two-dimensional experimental combustor.
在二元试验燃烧室上，研究了四种掺混孔设计方案对燃烧室出口径向温度分布影响。
The exit radial temperature profiles formed by four configurations of dilution hole design have been studied experimentally on a two-dimensional experimental combustor.
应用推荐