对机械制造中由于工件的测量误差及工艺尺寸的换算而引起的误收和误废进行了分析，做出正确的判断并采取相应的措施进行处理。
The analysis of the product accepted and rejected by mistake caused by the measuring error and the conversion of the technological size chain of the workpiece is carried out.
从测量误差分析及现场实践证明，该方法技术先进，测量数据精确。
It is demonstrated that the method is advance in technology and the measured data are precise by both error analysis of measurement and field practice.
介绍了一种多通道温度采集系统，详细分析了其测量原理及测量误差，给出了其系统设计。
The principle and error of high precise temperature measurement are introduced in the multichannel temperature measuring system. It also introduces the design of the system.
通过解决激光加工中材料表面温度测量装置的难点，设计了一套新型光学系统，并给出了测量误差分析及结论。
A new optical system is designed for the material surface temperature-measuring device used in laser processing. The measurement error analysis and conclusions are presented.
介绍了微机控制的阶梯轴多参数在线测量系统的测量原理、系统构成及测量误差分析。
The measuring principle, system composition and measuring error analysis of the computer controlled step shaft multi parameters on line measuring system are introduced.
分析了激光自混合干涉仪位移测量误差及特点，提出了干涉仪的设计原则。
Displacement measurement error and its character of self mixing interferometer are analyzed. The design ruler of self mixing interferometer is presented.
最后，分析了游标卡尺测量误差及标准球安装误差对标定结果的影响。
Finally, the influence of the measurementing errors and the positioning errors on the calibration was analyzed.
检校应用研究分为三个部分：数字信号源的校准研究、测量误差分析及最佳测量周期的确定。
The application research will include three parts: research on the calibration of digital signal source, error analysis and the best calibration interval.
与常用反时限保护特性相比较，此保护模型更符合负载的实际运行规律及保护要求，并对测量误差关系进行了分析。
Different from the common inverse time characteristic, this model conforms to the load actual operating law and the protection request, and takes the analysis of measurement error into consideration.
给出电路接口方式、测量误差分析及实验结果曲线，液滴体积随液滴生长过程呈现良好线性关系。
Interface circuits, error analysis and experimental result graphs are presented. Excellent linearity between the drop volume and drop growth is achieved.
着重分析了锥体重心测量系统测量误差的来源、算法及系统整体测量不确定度的评定，从而可以提高锥体重心的测量准确度。
The measurement error source of center of cone gravity, arithmetic and uncertainty of ATS are given, and the measurement accuracy of cone center of gravity is improved.
介绍了一种多通道温度采集系统，详细分析了其测量原理及测量误差，给出了其系统设计。
The principle and error of high precise temperature measurement are introduced in the multichannel temperature measuring system.
提出挠流阻力引起探针杆挠曲造成水流场测量误差的迭代计算修正方法，分析该方法的收敛性及收敛方式。
A method was proposed to correct errors in water flow field measurements with 5 hole probe because of rod bending caused by flow drag. The convergence of the computing method was analyzed.
本文论述了高精度大型轴类零件在位测量装置及系统的实现方法，并分析了在位测量误差产生的原因。
The dissertation involves the device and system implementation method for OSM of high-precision large shaft where the reasons for OSM errors are analyzed.
将转角传感器测量曲率半径方法应用于板材滚弯加工过程的成形检测之中，论述了采用转角传感器测量板材曲率半径的原理及其测量方法，通过试验研究分析得出该测量方法的优越性及造成测量误差的主要原因。
In this paper the method of volving angle sensor measurement of curve radius is used to examine the plate forming curve in the process of forming and its′ principle and methodology is explained.
本文介绍一种以差动传感原理测量冷却过程中釉层热应力的方法及装置，并对该装置的测量误差进行了分析。
The paper introduce a method and device of measuring stresses in glaze layer with differential sensing principle. When the glaze is cooled off. The error in measuring of the device was discussed.
本文介绍一种以差动传感原理测量冷却过程中釉层热应力的方法及装置，并对该装置的测量误差进行了分析。
The paper introduce a method and device of measuring stresses in glaze layer with differential sensing principle. When the glaze is cooled off. The error in measuring of the device was discussed.
应用推荐