通过测量信号在卫星和天线之间传播所需的时间，汽车的位置可以被锁定在100米误差之内。
By measuring the time required for a signal to travel between the satellites and the antenna, the car's location can be pinned down within 100 meters.
最后给出对实际测量信号的处理结果。
Finally, The processing results of practical measurement signals are given.
最后给出对实际测量信号的处理结果。
Finally, the processing results of practical measured signals were given.
它使用“高阻抗”传感器来测量信号，而不是制图电流。
It does so by measuring the signal without drawing current, using "high impedance" sensors.
本文介绍利用频谱分析仪测量信号相位噪声的方法。
A method of how to measure the signal 's phase noise by spectrum analyzer is introduced.
最后用软件细分法对测量信号进行高倍数数字细分。
Finally, digital subdivision is adopted to obtain high division number.
用户可以设定测量信号的直流偏压，测量振幅，脉冲宽度。
User may specify the DC bias, measurement amplitude, and pulse width of the measurement signal.
鼓风机的测量信号能同时满足DCS以及就地仪表盘的要求。
The surveying signal of air blower can meet the demands of DCS and the instrument panel on the spot at the same time.
广泛的监控可能性，如示波功能，测量信号的历史曲线显示等。
Extensive monitoring possibilities, e. g. oscilloscope function, history graph for measuring signals.
选择采样电阻，既要信噪比好，又要避免产生过大的测量信号。
Sampling resistance is both the signal to noise ratio to be good and avoiding to produce the oversized survey signal.
该方法能将测量信号的分析处理和故障的定位很好地结合起来。
The signal analysis and process can be conveniently combined with the faults location by this method.
利用锁相放大器追踪测量信号，微机自动扫描、采集和处理数据。
It USES a lock-in amplifier for testing the signal and a personal computer for automatic data scanning, collecting and processing.
实验结果表明，风机管道中空气流动对传声器测量信号的影响很大。
The experimental result shows that the measurements with microphone are highly sensitive to airflow in the fan duct.
介绍了自动去重加工的工作原理及测量信号转换的硬软件实现方法。
The automatic weight adjusting principle, hardware and software design of the weight adjusting signal process are introduced in detail.
同时，还研究了探测线圈屏蔽套筒给中心磁场及测量信号带来的影响。
Meanwhile, the influence to the central field brought with the shielding bushing is discussed.
本文系统论述了单孔法剪切波速测量信号处理中的一种到时差识别方法。
An S-wave arrival time detection method for wave velocity measurement in single-hole method is presented in this paper.
分析表明光强非均匀分布给波前曲率传感器测量信号带来了一定的误差。
Analysis indicates that nonuniform intensity introduces some error into wavefront curvature sensor signal.
论述侦收测量信号极化的重要性，并介绍信号极化的基本参数和测量方法。
This paper describes the importance of measurement of singal polarization in radar reconnaissance devices, introduces basic parameters and measuring method of singal polarization.
其测量信号是经过TA末屏电压信号放大器引入谐波信号数字测量分析系统的。
Its measurement signal is to lead into harmonic signal digital measurement analysis system via ta end screen voltage signal amplifier.
以热工测量信号为对象，研究开发了具有多种通信协议接口的通用数据采集装置。
A universal data acquisition device with multi interfaces of communication protocols is developed for acquiring thermal measurement signals.
该采集器尤为适用于双通路锁相放大器的正交矢量运算或双光路测量信号的处理。
This system is used as the data processor of measurement instruments to provide the instantaneous computed function.
数据级融合模块主要对多传感器的测量信号进行处理，提取出故障诊断的特征信息。
The data fusion level module mainly handles the metrical data of multi-sensors and extracts the feature of faults.
无线测量集中在移动台与基站之间，主要测量信号电平、信号质量、定时提前量等等。
Wireless measurements occur between MS and BTS and the major measurement parameters include signal level, signal quality, time advance and so on.
该传感器还借助微处理器对测量信号的非线性与温度漂移进行了数字化的修正和补偿。
The moisture sensor makes digital modulation and compensation on signal non-linearity and temperature offset by adoption of microprocessor.
单端基准点(rse)的测量系统是相对于地线测量信号的，有时也称为接地测量系统。
A referenced single-ended (RSE) measurement system, also called a grounded measurement system, is similar to a grounded signal source, in that the measurement is made with respect to earth ground.
传统的系统状态估计方法只用到连续信号，而离散测量信号所包含的信息没有得到利用。
While only continuous signals are utilized in traditional system states estimation approach, information contained in discrete measurements is ignored.
处理器的功能包括：1）测量信号参数，尤其是选定雷达的脉冲重复间隔（PRI）参数。
The functions of the processor are 1) measuring the signal parameters, especially the Pulse Repetition Interval(PRI) of desired signa.
利用相关积分方法的滤波特性可以有效地抑制测量信号中的噪声影响，提高参数估计的精度。
Using the filter property of correlative Integral, the effect of noise in measured signal may be effectively restrained and the precision of parameter estimation is raised.
利用相关积分方法的滤波特性可以有效地抑制测量信号中的噪声影响，提高参数估计的精度。
Using the filter property of correlative Integral, the effect of noise in measured signal may be effectively restrained and the precision of parameter estimation is raised.
应用推荐