这些临时测点均位于离城10公里以内。
These temporary observation posts were all within 10 km of the city.
同时还给出了一些重要测点上的主要测量结果。
Meanwhile, the measured results at several important points are given.
氧活化测井解释的关键是确定各测点的水流速度。
The key of oxygen activation logging interpretation was water-flow velocity which determined every measuring point.
提出了一种多工位薄板装配过程测点优化设计方法。
An optimal sensor design method was presented for the multistation sheet metal assembly processes.
系统采用拉曼光时域反射技术，对所测点进行定位。
The position of measurement point was determined by Raman scattering optical time domain reflection (OTDR) technique.
零件密集区之PCB（下有铜箔层），为板温量测点。
PCB with highly concentrated component, ( bottom is copper tinsel) that is the absolute point of measurement.
测点的数目由操作员决定，这个数量与精度要求有关。
Number of points to be tested is decided by the operator and is related to the accuracy requested.
最后以300MW机组为例，说明其振动测点的一般布置。
Finally, demonstrate the general layout of vibration signals for 300MW unit.
利用有限元软件建模和分析，得到测点位置的应力分析值。
FEM analysis is also performed to compute the stresses on the same points.
该系统是将各测点(分站)虚拟为中继站来实现多路由选择。
In this system, more routs are selected by dummy repeater technique.
本课题设计了一种具有多个测点的智能温度测量控制应用系统。
This topic designed one kind to have many measuring point intelligence temperature survey control application systems.
至于断层形变，则随测点与震中关系的不同表现出不同的特征。
As for the fault deformation, it expressed different features with the different relation between the station and the epicenter.
地形的起伏以及测点位置的准确性是否会影响重力测量的结果？
Do the topographical relief and the precision of the location of stations affect the result of gravimetric rneasurement?
通过数据采集，进行坐标转换，能够方便地计算出测点超欠挖。
Through data collection and coordinate transformation, the over-under-excavated values can be obtained easily.
卡钳，金属的直尺，卷尺，曲尺，中心冲，感觉测点作记号钢笔。
Venier caliper, metallic ruler, measuring tape, square, center punch, felt point marker pen.
试验测点：已完成通风试验和性能试验测点安装位置及加工图纸。
Test instrument point: Have fixed exactly installation position of ventilation and performance test including related drawings.
阐述了桥梁静载试验的加载原则、加载方案设计和测点布置规则。
The loading principle, loading project and rule of measuring-point arrangement for bridge static test are presented.
针对叶片零件数控加工工艺中的在线检测提出了两种测点规划方法。
The paper provided two methods of on-line probing measure-point layout for numerical control machining of blade parts.
这些参数包括模态数、采样频率、车速、响应测点位置和测点数等。
These parameters include mode number, sampling frequency, vehicle speed, locations and Numbers of measured stations.
标定试验结果表明，测点应变增量与残余应力间存在良好的线性关系。
The experiment results show that the measured additional strain keep a linear relationship with residual stress in the structure.
而对某一固定测点而言，其受上方圆柱的影响要大于受下方圆柱的影响。
While the upper cylinder gives more effect than the lower one that is located symmetry of the measure point.
利用该系统，有效地解决了热轧板厂各分散测点集中管理的关键技术问题。
The key technology problem of distributed test of the hot strip is effectively solved by central management.
本文利用有限元模态计算的结果，进行模态测试前的测点和激励点的优化研究。
Using the results of FE modal calculation, optimization of exciting and measuring positions have been carried out before the modal test.
重力测量中最大的困难就是取得高精度的地形图以及确定每一测点的精确位置。
The biggest difficulties in gravimetric observations are to get a first class map and the exact location of every measurement.
同时介绍了承台混凝土施工过程中的温度测试的测点布置方法和温度监测结果。
The method of how to lay out observation site during the construction of pier caps concrete and its temperature datum are introduced.
分析得出节点型钢腹板的剪应力方程，利用试验数据可求得腹板上测点的应力值。
Stresses in the steel webs were obtained by using the test data in the shear strength equation introduced from the analysis.
在印刷电路板受力边界粘贴电子应变片以应变电测技术和原理测定各测点的应变值。
Plaster the electron strain gauge on PCB stress boundary to measure the strain cost with both strain electrical logging technology and theory.
测量时必须严格按照规定的测点位置和测量项目的定义﹐使用可靠的测量仪器进行。
Measurements must be in strict accordance with the provisions of the measuring point and measuring the project definition, the use of reliable measuring instruments.
网络组的输入是定子测温系统提供的每一个测点的一段时间的温度变化过程的数据集。
The input of the network group is a data set of a period of time from a temperature measuring point.
为了求解两个同心圆的半径，必须计算分析各测点对之间的噪声相干性和信号相干性。
We must analysis the coherence of noise and signal of every site pairs for the comfirmation of the two radius.
应用推荐