唯一的挑战是，如何提取自旋来形成一个自旋极化的电流，然后注入到电路中并保持极化在沿途不发生退化。
The challenge, however, is extracting the spins to form a spin-polarized current and injecting them into a circuit without the polarization degrading along the way.
一个连续性测试器给电缆导线注入交流信号，从而找到电路故障。
A continuity tester injects an AC signal into the conductors of a cable to find circuit faults.
采样保持电路设计采用了电容下极板采样技术，不仅有效地避免了电荷注入效应引起的采样信号失真，而且消除了时钟馈通效应的不良影响。
The sample and hold circuit is employed by the bottom plate sampling technique, which could not only cancel the charge injection error but also eliminate the effect of clock feed-through.
对读出电路的注入效率进行了计算机模拟。
The injection efficiency of the ROIC is simulated by the computer.
直流侧纹波消除电路是基于直流线路中纹波的直接再注入原理而设计。
The circuits of dc-side ripple reduction are based on direct reinjection of the ripple in series with the dc line.
用离子注入技术保证电路具有较好的一致世。
The ion implantation technology is used for a good uniformity of the circuit performance.
在基于对等效电流源电路模型分析的基础上，推导出了单相单位功率因数变流器输出电流二次谐波的计算公式，将输出二次谐波电流正、反向交替注入交流输入侧来抵消电流中的谐波。
Derived the formula for computing quadratic harmonics of output current in the single phase unit power factor ac DC converter based on analysis of the circuit module of the equivalent current source.
就目前而言，已有的离子注入技术(包括离子注入设备系统)尚不能满足甚亚微米器件和电路制造的需要。
Now, the present ion implantation technology, especially ion implantation equipment and systems, can not meet the needs in the manufacturing of deep submicron devices and circuits.
使用该方式电路，室温下半导体激光二极管注入电流波动为10- 5，温度波动优于10- 4。
Using the circuits, the fluctuation of injection current is 10 -5 and the fluctuation of case temperature is better than 10 -4 under the room temperature.
现代半导体集成电路的制造往往要求涉及大电流低能量带电搀杂剂原子的注入步骤。
The fabrication of modern semiconducting integrated circuits often requires implantation steps that involve high currents of low-energy charged dopant atoms.
为了验证设计的有效性，使用TMS320C 6713DSP搭建验证电路平台，采用软件故障注入法对设计进行验证。
In order to verify the effectiveness of the design, we build an test platform using TMS320C6713 DSP, on which the software fault injection method is adopted to verify our design.
文中着重介绍了注入离子能量、剂量、退火温度及时间对电路元件电学性能的影响。
Tbe present paper is devoted to describe the effect of the implanted energy, dose, and annealing temperature and time on electrical characteristics of circuit components.
其次，文章重点对电容注入方式的并联混合型有源电力滤波器的电路结构、工作原理、谐波检测方法、控制方式、电路设计进行了理论分析。
The theoretic analysis is accomplished on the circuit topology, principle, harmonic detecting method, control method and circuit designing of Parallel Hybrid Active Power Filter (PHAPF).
MOS结构中光注入时外电路电流特性与绝缘膜中陷阱俘获截面密切相关。
The external circuit current of photoinjection in MOS structures is closely related to the capture cross section of traps.
本文介绍了在电流注入试验中实现时间关联的方法，并采用该方法得到了典型电路失效概率分布。
In this paper, the EMP failure modes of solid state relays were obtained by current injection method.
提出了电流注入探头的两种电路模型：集中参元电路模型和分布式传输线模型。
In this work, a lumped-parameter circuit model and transmission line model are discussed.
介绍了开关电流电路的基本单元结构，讨论了影响故障诊断精度的主要因素，重点分析了电荷注入误差。
The basic unit structure of the SI is introduced in this paper. It also discusses the main factors which affects the precision of fault diagnosis and analyzes the charge injection error in detail.
本文针对混合型有源电力滤波器的电路拓扑，介绍了无源注入支路的基本工作原理，重点阐述了如何选择注入支路的调谐频率。
In view of the topology of the hybrid active power filter with injection circuit, analysis its principle in detail, as well as choice the desirable resonance frequency.
本文针对混合型有源电力滤波器的电路拓扑，介绍了无源注入支路的基本工作原理，重点阐述了如何选择注入支路的调谐频率。
In view of the topology of the hybrid active power filter with injection circuit, analysis its principle in detail, as well as choice the desirable resonance frequency.
应用推荐