生成中间帧的方法有线性插补法和高次多项式拟合法等。
The usual methods of building in-between frames include linear interpolation method and higher order spine interpolation.
制冷工质的热物理性质使用隐式三次多项式拟合模型计算。
Refrigerant's thermal physical characteristics are calculated according to implicit cubic polynomial curve-fitting model.
采用响应面法建立了表示比吸能随材料参数而变化的曲面，和高次多项式拟合时的相对误差曲线。
Then the response surface method(RSM) is utilized to establish the response surfaces or curve of SEA vs. material parameters and the curves of relative error in high-order polynomial fitting.
为此对某型航空发动机的离散试车数据点进行了多元高次多项式拟合，建立了该型号发动机的稳态特性曲线。
While the discrete test run data of an aero-engine was adapted using the high order multi-parameters polynomial fit method, the steady characteristic curves were founded.
本文首先阐述了四次多项式拟合的基本原理以及精度评定方法，然后具体算例，实际计算分析了此种拟合方法的精度。
Firstly, the author discusses the theory of the fitting method and precision estimate, and then analyzes the precision through calculating a practical example.
研究结果认为：(1)天敌胁迫下的棉蚜的年趋势可以用一个三次多项式来拟合。
The result was as follows: (1) The year trend of cotton aphid intimidated by natural enemy is pictured with a three cubed polynomial.
提出织物的二维悬垂曲线可用3-4次多项式曲线拟合。
The fabric drape curves in two dimensions can be fitted to the 3-4 times polynomial curves.
然后利用二次多项式模型拟合文本行的中心线，并建立径向失真校正的目标函数。
Then, it used second order polynomial to fit the Central Line of text line, and constructed the object function of lens distortion.
本文采用三次多项式插值和曲线拟合相结合的方法可简单有效地提取出在线掌纹的线特征。
In this dissertation, a line extraction method based on cubic polynomial interpolation and minimum mean square error fitting are proposed, which can effectively extract lines out.
本文从寻找一种精确拟合大角度入射时反射系数随入射角变化的方法入手，提出一个与泊松比有关的二次多项式。
The authors'attempt is to find out an approach by which reflection coefficients can vary with incidence when large incidence is best fitted.
用七次幂多项式拟合片体线型和主体横剖面面积曲线，以线性兴波阻力理论为基础计算兴波阻力；
By approximating the lines of the demi-hull and the main body's section with 7-order polynomial, the authors calculate the wave-making resistance of a SWATH based on the linear theory.
但二次多项式只能拟合x坐标与Y坐标之间成函数关系的点序列，无法拟合闭合曲线。
But the quadratic curve can be used only in condition when each X-coordinate of the points sequence mapping to only one Y-coordinate, so it can't be used in fitting closing curve.
汽蚀曲线绘制方法有传统的有手工绘法、多项式拟合法、非线性拟合法、三次样条插值法等。
Cavitation curve drawing method of the traditional hand-drawn method, polynomial fitting, non-linear fitting, cubic spline interpolation method.
并通过对动态测量中某霍尔位移传感器位移-电压数据进行了坏值剔除和三次多项式非线性拟合，表明动态测量中传感器数据的非线性处理方法。
The curve of a Hall displacement sensor is obtained by polynomial fitting. The method of data erasing and curve fitting can be applied in processing the data of sensor in dynamic measurement.
并通过对动态测量中某霍尔位移传感器位移-电压数据进行了坏值剔除和三次多项式非线性拟合，表明动态测量中传感器数据的非线性处理方法。
The curve of a Hall displacement sensor is obtained by polynomial fitting. The method of data erasing and curve fitting can be applied in processing the data of sensor in dynamic measurement.
应用推荐