相反，在类中编写通用方法以模拟以上的操作就比较合适了，它继承了appobjects文件夹中的GUI对象类。
Instead, it's good to write a generic method in a class to simulate the above action, which inherits the GUI object class in the appobjects folder.
本部分向您介绍如何使用模拟来标识原有流程中的问题，并介绍如何使用模拟和动态分析方法将其与将来版本进行比较以显示改进之处。
This section shows how you can use simulation to identify problems with As-Is processes, and how to show improvement comparing them to the to-be version using simulation and dynamic analysis.
如果您使用迭代化方法，比较理想的，您的测试环境应该能后映射您的成果环境；最起码，能够模拟该环境。
If you use an iterative approach, ideally, your test environment should mirror your production environment; at a minimum, it should simulate that environment.
在此基础上，分析比较当前过程系统的分析与模拟方法，根据锅炉热力系统的特点选择合适的过程分析模拟方法。
On the condition of it, choose an appropriate process analysis method for boiler thermal system, after comparing the present simulation methods of process-system.
模拟计算结果与试验数据的比较说明了所提出的汽车侧向振动模拟方法的有效性。
A good agreement between simulation results and experimental data shows the effectiveness of the simulation method for automobile lateral vibration.
通过模拟结果与热电偶测得的特征点温度曲线的比较，验证了热模型和模拟方法的正确性。
Correctness of the thermal modeling and the simulation method is validated by comparing simulated result with temperature data gained from characteristic positions.
进行了室内模型模拟实验，通过实验结果与反演结果的比较验证反演方法的可行性及准确性。
Carry on indoor model simulation experiment, through experimental result with perform comparison verification of result of analysis on feasibility and accuracy of method instead.
文中分析、比较了测量逆变器效率的三种方法后，提出采用模拟相乘方法作为硬件处理方案。
In this paper, three methods to measure the efficiency of inverter have been discussed and compared. Based on the conclusion, analog multiplication method is employed.
讨论了它的性能特点，用计算机模拟方法与CFDM、CVSD、SVADM和HCDM等已有adm方案进行了比较。
The performances are discussed and compared with the known ADM methods such as CFDM, CVSD, SVADM and HCDM by means of computer simulation.
为了验证双向蒙特卡罗法模拟热辐射传递，与文献中其它方法计算结果进行了比较。
To validate the Bidirectional Monte-Carlo simulation for radiative heat transfer, the solution obtained from this method is compared with that from other methods.
在不考虑自吸毛细管压力和滞后现象的情况下，采用饱和度端点比例将这些模拟结果与传统模拟方法进行比较。
The results of these simulations are compared with traditional simulation approach using scaling of saturation end points and not accounting for imbibition capillary pressures and hysteresis.
本文比较了以往试验中采用的几种边界模拟方法，认为采用柔性容器的效果较好。
Through comparing several boundary simulation methods used in past tests, this paper draws a conclusion that the effect of the flexible boundary box is satisfactory.
论文中对装置的主体电路结构、主控芯片的选择、模拟量输入通道设计和A/D采样方法进行了详细的方案比较和论证。
The main structure of the device, the selection of the microprocessor, the design of analog inputs, and the A/D sampling method are argued in detail in this dissertation.
根据啮合原理，提出了计算机模拟创成方法并同其它爪型干式真空泵的容积利用系数做出了比较。
Using the meshing principle, we raise computer-simulated generation method and compare volumetric efficiency with other kind of claw type dry vacuum pump.
采用数值模拟和实验相结合的方法比较了常规结构和一种特殊结构双载体三效催化转化器的性能。
The performance of dual-bed three-way catalytic converters with conventional structure and a particular structure was compared by numerical simulation and experiment.
最后通过能耗模拟，比较了动态计算方法和有效传热系数法的差别。
Finally through simulation of energy consumption, we analyze the difference between dynamic analysis method and the effective heat transfer coefficient method.
用蒙特-卡洛模拟方法对纵向阶乘矩和横向阶乘矩进行了比较和研究。
The difference in the horizontal and vertical factorial moments is compared and studied using Monte-Carlo simulation.
比较了不同的能量打分函数、能量优化(EM)以及分子动力学(MD)模拟方法对区分近天然构象的作用。
In this method, we compared the effect on discriminating near-native structures of different scoring functions, energy minimization (EM) and molecule dynamics (MD).
数值模拟结果与实测资料和物理模型试验结果的验证比较表明，该方法可以定性分析漂浮物的堆积形态。
Comparison between numerical simulation and measured results of the physical model test shows that this model can qualitatively simulate the floating-debris' accumulation form.
在多方案比较时，采用二维模拟的方法，节省了计算时间，降低了计算成本。
Two-dimensional simulations are performed in comparison of schemes, which saves a lot of time and decreases the computing cost.
由于本文的研究采用格点模型模拟方法，为了选取一种合适的折叠模式，本文比较了两种折叠模式的热力学和动力学性质。
In order to select one for the following simulation, the thermodynamic and kinetic properties of a lattice protein model by using the two move sets were calculated and compared.
在模拟试验的基础上，比较了微观结构效应对两种波动率度量方法的影响程度。
Under simulated tests, the effects of microstructure on realized range-based volatility and realized volatility are compared.
采用数值模拟方法对机翼型及板型叶片的轴流风机的气动性能进行了比较。
By numerical simulation method, the comparisons of aerodynamic performance between airfoil and plate blade axial fans were made.
本文首先通过理论分析和数值模拟，比较了界面追踪技术中VOF方法的三种界面重构技术。
In this thesis, the first work is to do a comparison of three kinds of interface reconstruction methods which are applied to the volume of fluid (VOF) method.
利用数字滤波器的不同模拟化设计方法，进行了计算机上的设计实现，检验并比较了不同形式的数字滤波器的设计方法的特性。
Digital wave filters were designed with the computer by use of different simulation design methods, and the design features of different digital filters were checked and compared.
在第五部分中，蒙特卡洛模拟结果提供了新的估计并且还与其他方法做了比较。
In Section v, Monte Carlo simulation results are provided for the new estimator and compared with other methods.
本文用实验和数值模拟的方法，比较了不同重力下有限空间内热薄材料表面的逆风传播火焰。
In present paper, opposed-flow flame spread over a thin solid material in narrow channels in different gravity was compared experimentally and numerically.
方法提出适宜的新公式，用医学资料实施计算机模拟实验，将新方法与旧方法比较。
Methods The one has been advanced, and it has been compared with old method by medical examples as simulating experiment in computer.
数值模拟的结果与试验结果吻合得比较好说明了所建立的模拟复合材料结构耐撞性的策略与方法是可行的。
Numerical results are compared well with experimental results, thus the established FEM-based numerical strategy and means is verified.
数值模拟的结果与试验结果吻合得比较好说明了所建立的模拟复合材料结构耐撞性的策略与方法是可行的。
Numerical results are compared well with experimental results, thus the established FEM-based numerical strategy and means is verified.
应用推荐