实现了注塑模具脱模方式选择的智能化和结构设计的三维参数化。
The intellectualized choice of the ejection fashion of the injection mold and the three- dimension parameter of the structure design are realized.
本文通过论述模具脱模斜度对模具尺寸的影响、塑料件未注公差的确定，并通过一个设计实例进行了说明。
In this paper, the impact of draft Angle to the moulding dimensions and the comprehension of the dimensions in plastic production with the unlabeled tolerance were discussed.
影响脱模的原因常常是差的模具冷却效果，而这又是由于缺乏冷却剂，而不是温度的设定所致。
Frequently the cause is poor mold cooling and this is frequently caused by a lack of coolant rather than its temperature.
适用于各种模具的脱模，保养和清洁，使用方便，脱模效果好。
Applicable to a variety of mold release, maintenance and cleaning, easy to use, Demoulding effect.
举例用的模具是由六个板组成的包含型芯、脱模衬套、齿轮和齿条以及止推片、轴瓦和方形密封圈载一起的冷端或“B”面。
For used molds are composed of six panels contains the core, Demoulding Bushing, gear and rack and the thrust piece, bearing and seal set with a square of the cold-side or "b" side.
本发明制备方法简单、所需设备吨位小、脱模时间短、对模具没有严格要求及成本低廉。
The preparation method is simple, has small equipment tonnage required, short demoulding time and low cost, and has no strict requirement on the die.
依次将面层和底层混合料布于模具中，加压成型、脱模、静养、码垛、养护，得到渗水防滑硫铁矿烧渣彩色花砖。
Spread the pavement surface and bottom mixtures into the die, pressure molding, demould, stay, palletize and maintain to get the seepage and antiskid colorful tiles made of pyrite cinder.
水太多会减少粘附力，加水太少则会使脱模剂在模具表面堆积太厚。
Too much water reduces the adhesion and too little piles the material up too thick on the mold surface .
需要使用金属模具和脱模剂例如滑石粉末。
通过对有内螺纹的塑件结构分析，确定采用齿轮齿条机构脱模的模具结构。
Through analyzing the structure of plastics with inner screw, determined mold structure with gear and rack stripping screw mechanism.
通过计算设计了注塑模具的成型结构、 脱模机构、浇注系统等方面。
The design includes the mould structure, the mould cavity, the pour system, and so on.
实践证明，强制脱模的模具结构简单，成本低，使用效果好。
The application showed that the mould design was simplified, the cost was lowered and the efficiency was raised.
该模具利用斜面改变推力方向原理，采用三脚推管实现斜插座铸件斜向脱模。
Making use of the principle that a inclined plane can the direction of a force, a three legged ejector sleeve is adopted in the die casting mould to take cast stripping mould.
模具设计成斜导柱侧抽芯，利用复位杆复位，以顺利脱模。
The die with oblique side of guide pillar to take out core and release link was designed to take off mould smoothly.
本实用新型的气动脱模软糖模具具有生产效率高、产品平整光滑、易生产自动化等优点。
The pneumatic demoulding soft sweet mould of the utility model has the advantages of high productive efficiency, flatness, smoothness, easy production, high automation, etc.
在模具内浇注预养好的坯体，由翻转吊装机构将模具整体经空中翻转90度后放置于切割小车上进行脱模。
Mould the base body in the mould, and lay on the cutting trolley for demoulding after turning the cast mould over 90 degree by the upset hoist.
介绍了斜齿轮塑件注射成型模具的齿形型腔旋转式和斜齿轮塑件旋转式两类脱模机构设计。
The whirly demoulding mechanism designs of shape-gear and the whirly plastic parts of bevel gear injection mould were introduced.
这种模具可使塑件自动脱模，大大提高了生产效率。
The mould is separate automatically from plastic, and raise productivity.
针对大型、深腔、薄壁筒形件脱模较大，及要求成型后变形小的特点，采用气动的脱模方式进行了注射模具的设计。
Design the injection molding with pneumatic ejecting, so as to suit the injection molding with big ejecting force in deep mold and thin wall barrel.
玻璃幕墙的模具涵盖罚款层油脂脱模代办署理人。
The glass walls of the mould were covered with a fine layer of a grease demoulding agent.
对双层共12个不同方向同步抽芯脱模典型结构以及模具制造和试模时应注意的问题作了叙述。
The structure of 12 of the double core-pulling in different directions, the points which should pay attention to when making and trying were described.
判定脱模方向是实现模具自动设计的第一步，也是评估塑件或浇注件能否模具成型的重要因素。
Mold parting direction is an important factor to verify the moldability of a molded part and its determination is the first step to achieve automatic design of injection mold or casting die.
详细介绍热流道模具浇注系统结构设计和尺寸计算、热流道板加热功率计算、热流道板线膨胀量计算及在设计时应注意的一些问题，并介绍了一种二级脱模机构。
The structure design and the calculation of the sizes, heating power, linear swell value of hot runner system were discussed in detail. A two-step demoulding mechanism was also introduced.
另外建压时间、坯料加热温度、模具预热温度以及脱模剂等参数对半固态压铸件性能也有明显的影响。
Furthermore, the property of die castings have also been affected obviously by other process parameters, such as time of intensified pressure, mould temperature, billet temperature and lubricant etc.
脱模时只需按相应按钮顶出模具里的试件，自动实现脱模，非常简单方便。
Get the molding tool out can just push the correspond button, the instrument can push the molding tool out auto, makes it very simple.
该模具消费的制件是长壁制件，脱模后贴在型芯上，推出机构用的是接近制件壁穿型芯的推杆。
The mold of the parts is parts of the wall, after Stripping posted on the core, the agency launched using a wall around parts wear core putt.
模具结构中采用了定模强制脱模，顺序开模，滑动型芯延时顶出等机构。
Several mechanisms such as forced stripper, sequenced opening, delayed goring of the sliding core are applied in the design.
对带内螺纹的塑料制品及其模具结构进行分析，采用自动卸螺纹和压缩空气二次顶出相结合的结构较紧凑的脱模机构。
The product with inner thread and its mould structures are analyzed. The demoulding structure of automatic thread demoulding and second ejection with compressed air are adopted.
对带内螺纹的塑料制品及其模具结构进行分析，采用自动卸螺纹和压缩空气二次顶出相结合的结构较紧凑的脱模机构。
The product with inner thread and its mould structures are analyzed. The demoulding structure of automatic thread demoulding and second ejection with compressed air are adopted.
应用推荐