用计算机绘制根轨迹克服了传统方法的缺点，有效地提高了精度和速度。
The method is better than the traditional handcrafted method and raise the accuracy and speed effectively.
讨论了固体激光器中以两根串联氪灯为负载时所用高精度激光电源的方案选择及技术要点，探讨了激光电源精度提升的新思路。
It is discussed the scheme to select the circuits and some technical essentials of high-accuracy laser power in solid-laser, when the load is two series-connected Kr lamps.
在达到同等阻尼效果时通过增加钢筋根数，提高了系统的微调能力和模拟波形的精度。
The objective of increasing the steel bar′s number, achieving the same damping effect, and improving the tiny adjusting ability and the precision of simulating wave are all realized.
此外，土壤质地、石砾多少、微根管材料选择、减少光系统对根系的干扰等也是影响微根管测定精度的因素。
Soil texture, tube material, and disturbance of light on root were also the factors affecting the precision of the method.
高精度拖板往复线性导轨：确保盖板磨砺的根差。
High capability guide board is adopted for insuring same flat after grinding.
本文提出一类不依赖被估计系统模型微分状态估计器，参数少、精度高，通过分析其根轨迹和极点要求配置合适的参数；
This paper presents a new differential state estimator, which does not rely on the model of the estimated system and has higher accuracy with a few parameters.
微根管观测精度主要取决于微根管安装的质量和数量、微根管取样间隔期和取样数量、微根管图像分析技术等。
The factors affecting fine root measurement and its precision mainly included the quality and quantity of tube installation, sampling interval and quantity, and analysis technique of images, etc.
主要用于同轴电缆及特殊单根线的加工，采用最先进的旋转刀架，提高了加工的精度和速度。
It is mainly used for processing of coaxial cable and special single wire. It adopts the most advanced turning knife rest to increase the processing precision and speed.
进一步，即使可以精确地得到特征方程，我们依然无法在有限精度的限制下去计算方程的根。
Furthermore, even if the exact characteristic equation can be obtained, we could not compute the roots of the equation in the demanding precision.
主要介绍了RTK技术在地形图图根测量、碎部测量中的可行性和操作步骤及注意事项；并详细分析了该方法的测量精度。
The paper brief introduced the feasibility, handle operate steps and notice of RTK technique used in the survey of secondary control and detail survey, and detailed analyzed the precise of this way.
主要用于同轴电缆及特殊单根线的加工，采用最先进的旋转刀架，提高了加工的精度和速度。
Mainly used for a single line, coaxial cable, and special processing, using the most advanced rotary tool carrier, improve the processing accuracy and speed.
简述全站仪的构成及测设图根控制点的基本原理，分析布设图根控制点的测量精度并得出结论。
The form of electronic total station and the basic principle of determining and setting up root control points were related briefly. The accuracy of setting up root control points was analysed.
特别要研究总结在不同管口组对精度条件下，实施单面焊双面成形根焊的技术和工艺效果。
Will study summary especially in different orifice group for precision condition take off , implement single surface to weld the two-sided shape technical and technology effect of welding thoroughly.
该法经在渭河临潼至华阴河段实际运用，其精度较传统马斯京根法有明显的提高。
The method has been practically used at the section of Lintong-Huayin of the Wei River and its precision notably increased co…
该法经在渭河临潼至华阴河段实际运用，其精度较传统马斯京根法有明显的提高。
The method has been practically used at the section of Lintong-Huayin of the Wei River and its precision notably increased co…
应用推荐