但其核心是Powertrack电源接线板，它表面是一个不到两厘米宽的沟槽，外面用两片胶皮封闭。
But at its core is a power strip — called the Powertrack — with a single trench less than two centimeters wide, concealed by two rubber flaps.
体育场馆场地照明专用电源装置是场地应急照明关键设备之一，其核心参数是切换时间。
Special power supply for stadium and gymnasium field lighting is one of key equipments for field emergency lighting, this installation's key parameter is transfering time.
DC变换器是开关电源的核心部分，有着极其丰富的动力学行为。
DC-DC converters are the kernel parts in the switching power supplies. There are abundant dynamical behaviors in them.
本文使用双电流控制模式，以智能芯片uc 3842为核心，设计了单片开关电源的实用电路。
In this paper, by the use of dual-current control mode and intelligent UC3842 chip as the core, a single-chip switching power supply circuit are presented.
控制系统以16位数字信号处理器TMS320F 240为核心，对整个电源进行了实时的闭环控制。
To realize real time closed loop control, high performance 16-bit DSP TMS320F240 is adopted as control kernel.
压电陶瓷驱动电源是压电式喷墨打印机的核心部件。
The piezoelectricity ceramic power supply is the core components of piezoelectricity ink-jet printer.
电源是各种电子设备的核心。
设计了一种以电流型PWM控制器UC3842芯片为核心的高频单端反激式开关稳压电源。
A high frequency single-ended flyback switching power supply is designed with current-mode PWM controller UC3842 chip as its core.
超声电源是进行超声冲击的能量供应和控制核心，因此它的性能好坏直接影响超声处理的质量。
Ultrasonic power supply is the power and control center of ultrasonic peening. Its performance directly affects the quality of ultrasonic peening.
蓄电池是变电站直流系统的基本组成部分，是重要的储能设备，也是不间断电源的核心。
Battery is a basic part of substation DC system, and it is the important device of energy storage and the core of uninterrupted power system.
该系统由核心处理器板、电源管理电路、LCD、触摸屏、按键、锂电池等组成。
The set is consisted of kernel processor board, management circuit of power supply, LCD, touching screen, push-button and lithium battery etc.
以SPCE061A单片机位核心，研制了高效、适用的控制系统，包括两个电源的驱动、软启动、净化器的按键及遥控等电路。
This paper studied control system with the center of SPCE061A MCU, including the drive and soft-start circuit of two power supply, the key and distance control of the cleaner.
高频高压脉冲电源是介质阻挡放电的核心部分。
The high-frequency and high-voltage pulse power source is the core part of the dielectric barrier discharge.
采用以射频卡U2270B器件为核心完成支撑电路设计，包括电源模块、频率模块、天线模块和数据输入；
The circuit design is carried out by taking chip of RF-ID U2270B as core, including power module, frequency module, antenna module and data input;
传感器节点主要包括核心模块、电源模块、无线通信模块、数据采集模块和RS- 232通信模块。
Sensor nodes consist of core module, power module, wireless communication module, data acquisition module, and RS-232 communication module.
系统硬件电路主要由数据采集部分、核心处理器模块、显示模块、数据存储模块和电源模块组成。
The hardware circuit is constituted mainly by the sections of data collecting, core processor, displaying, data storing and power supplying.
主电路为单电源供电，控制电路以高性能单片机80c 196kc为核心，实现了对喷焊过程的自动控制。
Its principal circuit is that of single power supply and the control circuit takes the high-performance monolithic computer 80c196kc as its kernel to implement automatic control of hardfacing process.
针对晶闸管中频电源的核心——逆变电路，提出了一种基于80c 196MC单片机的控制电路，给出了其构思的硬件和软件设计。
This paper introduces a new inversion control circuit based on 80c196mc microcontroller for thyristor medium frequency power supply. Meanwhile the hardware and software designs are also provided.
文章介绍了基于80c 196kc为控制核心的激光雕刻机控制系统的硬件设计，实现了对混合式步进电动机和激光电源的控制。
The paper introduces the hardware design of the laser engraving system based on 80c196kc, the control of hybrid step motors and laser power supply.
介绍了基于80c 196kc为控制核心的激光雕刻机控制系统的硬件设计，实现对混合式步进电机和激光电源的控制。
The paper introduces the hardware design of the laser engraving based on 80c196kc, the control of step motors and laser power supply.
以微处理器at89c 2051单片机为核心介绍了红外遥控编码的接收、解码及电源开关的控制方法。
Methods for controlling reception, decoding and power switching of infrared remote control encoding are described on the basis of microcomputer AT89C2051 single-chip processor.
本文以滑模变结构为控制核心，研制了以DSP为控制芯片的全数字化全桥移相软开关电源。
This paper presents a digital controlled full bridge ZVS PWM switching power supply, which is based on sliding mode control method by using DSP.
本文的信号电源就是变频电源在测试领域的应用，本文就信号电源的核心逆变器部分做了详细的分析和设计。
The signal power supply that this thesis proposed is a frequency variable power source used in test field. This thesis concentrates on analysis and designing the nuclear part: Inverter.
基于直流屏的电源监控系统的各模块功能划分与采样通道多等特点，设计了以MSP430单片机为控制核心，CPLD扩展端口的控制系统。
Based on function partition of modules and much sampling channels of power monitoring system for DC screen, a control system which takes MSP430 as control core and CPLD as extending ports is designed.
变速恒频电源数字控制技术以dsp作为控制核心，主要实现对变换器的控制和发电系统电压调节，同时也实现了系统保护功能。
Digital control of VSCF power system, which USES DSP as its control core, realizes the control of inverter and voltage regulator, as well as the system protection.
智能双电源控制器以P 87c591单片机为核心，是双电源切换开关的核心检测及控制部件。
Intelligent dual power supply controller takes P87C591 single chip machines as the core, which is the core test and control component of dual power supply switching switch.
软开关技术是解决逆变弧焊电源可靠性的核心技术。
Soft switching is the key technology to improve the reliability of inverter arc welding power.
水火电是我国未来电力市场中参与市场竞争交易的主要电源类型，水火电优化配置市场机制是我国电力市场设计的一个核心问题和全新课题。
The optimization configuring market mechanism of hydro-thermal power system is one of the core contents of the power market design and fire-new task in our country.
介绍一种利用占空比与PWM电路补偿端电压之间的关系，设计的以差动电压放大器为核心构成的占空比测量电路；它能以数字显示形式直接给出脉冲电源输出电压的占空比。
A duty ratio measuring circuit, which using differential voltage amplifier as core component, was designed utilizing the relationship between the duty ratio and the compensatory terminal of PWM IC.
介绍一种利用占空比与PWM电路补偿端电压之间的关系，设计的以差动电压放大器为核心构成的占空比测量电路；它能以数字显示形式直接给出脉冲电源输出电压的占空比。
A duty ratio measuring circuit, which using differential voltage amplifier as core component, was designed utilizing the relationship between the duty ratio and the compensatory terminal of PWM IC.
应用推荐