通过正交设计及极差分析法确定了最佳工艺条件。
The optimum technological conditions were determined by orthogonal test and extreme difference analysis.
通过正交实验和极差分析确定了影响增稠性的显著性因素。
The significant factors for the thickener was determined by orthogonal experiment and range analysis.
它可以帮助用户安排正交表和实现材料试验过程中的数据处理（包括极差分析和方差分析）。
The software can find its use for data processing of material experimentation and dealing with orthogonal scheme. This software also can be used in analysis of variance and analysis of range.
通过正交设计及极差分析法确定了最佳工艺条件，产品收率达80%以上，纯度可达94%。
The optimum technological conditions were determined by orthogonal test and extreme difference analysis. The yield of product reaches over 80%, and the purity is up to 94%.
论文用重标极差分析方法证明了中国股票收益波动的自相似性，长期记忆性和初始条件敏感性。
We use rescaled range analysis to demonstrate that there are self-similarity, long memory and sensitive to initial value in the time series of Chinese stock returns.
采用正交试验的极差分析和方差分析方法，分析了不同干燥参数对干制菠菜品质和能耗的影响。
The influence of microwave drying parameters on the quality of dried spinach and energy consumption have been analyzed by analysis of range and variance of orthogonal experiment.
通过正交实验和极差分析，优化了竹纤维织物阳离子改性、直接染色和不同媒染的最佳工艺条件。
The cationic modification of bamboo fibers, the direct dyeing and the different mordant dyeing conditions were optimized by orthogonal expts. and range analyses.
采用正交设计方法和通过极差分析研究了电弧喷涂工艺参数对J CW - b涂层结合强度和耐磨性的影响。
The influence of arc spraying parameters on the adhesive strength and wear-resistance of JCW-B coating was studied by orthogonal design test and extreme analysis.
对e - 20进行了填料改性及固化剂配置，并且通过正交试验与极差分析，对涂层性能作了较为深入的研究。
Orthogonal test and range analysis are used to study the performances of coatings when combined with different modified fillers and curing agents.
利用极差分析对花岗石加工过程中各因素影响各切削力的显著性进行了分析，得出了各因素影响切削力的主次关系。
The significance of granite processing factors influencing cutting force was analyzed by using range analysis. Then the influence relationship between various factors and cutting force was gotten.
将模拟结果同实际成形件厚度比较，通过极差分析，得出上述因素对前翼子板成形的不同影响，其中压边力、虚拟凸模速度对成形影响较其他因素大。
Then the result was compared with actual thickness value of forming part. Through the analysis of range, the effect of above elements on the forming of front fender was obtained which in...
讨论了测井数据的分形分析中经常遇到而又容易产生误差的问题，特别是重标度极差分析和功率谱分析方法中的不一致性以及在分形分析中如何处理原始测井数据。
The measured data about the initial deviations of the joint positions of several experimental models and an actual structure are studied carefully by the assumption and test methods.
总体上，混有添加剂煤粉的燃烧率相对于未添加任何物质的基准试样煤粉提高了20%左右，并对试验结果进行了极差和方差分析。
On the whole, the combustion efficiency of the coal powder with additives increases by 20%; meanwhile, the range analysis and variance analysis are used with the experimental data.
实例表明，应用灰色关联度分析方法可以准确地诊断和定位极差式空气压缩机的故障状态。
The example showed that the failure state of differential piston air compressor could be diagnosed and located correctly by using gray incidence degree analysis method.
提出了席位公平分配的最小极差法及其数学规划模型，比较分析了多种不同席位分配方法，并提出了非完全分配的概念及其数学模型。
This paper presents the method of minimum difference of poles on fair allocation of seats and its mathematical programming model, and analyses several methods of allocation of seats number.
检具需在安装产品后用三坐标进行重复性、再现性研究，重复性再现性R&R须符合QS9000/MSA测量系统分析（均值和极差法）第三版标准。
The checking fixture must be measured on CMM after installing IP ASM. part. The R&R% should conform to the standard of QS9000/MSA v3.0(the average and range method).
对于含量较小而极差较大的硫苷采用分段建模，可提高分析结果的准确性。
Results can be improved by calibrating sectional model for low content and large range total glucosinolate.
对于含量较小而极差较大的硫苷采用分段建模，可提高分析结果的准确性。
Results can be improved by calibrating sectional model for low content and large range total glucosinolate.
应用推荐