本文用该方法分析了环板弯曲问题。
提出了求解各向异性板弯曲问题基本解的新方法。
In this paper a new method for solving fundamental solution of anisotropic plates bending is proposed.
最后便可得到斜角板弯曲问题的近似程度较高的解。
In consequence the problem of bending of skew angular plate is solved with a better degree of approximation.
本文从基础板弯曲损伤概念出发引出弯曲损伤变量。
In this paper according to the concept of bending damage of baseplate, the bending damage variable is defined.
九参数广义协调元是板弯曲问题收敛性很好的有限元。
The nine parameter generalized conforming element is an effective element for the plate bending problem.
文中还给出了物体动变形及板弯曲等实测结果及分析。
Test results and analysis of the recorded dynamic deformation of a moving object and plate bended deformation are presented.
本文推导了平行四边形板弯曲问题的斜座标基本公式。
In this paper, fundamental formulas have been derived for the bending of a parallel quadrilateral plate in the incline coordinates.
本文建立了弹性地基上的矩形板弯曲微分方程的一般解。
This paper gives a general solution of differential equation for solving bending problem of rectangular plates on elastic foundations.
推导了以显式表示的12个自由度的简单矩形板弯曲元素刚度矩阵。
A stiffness matrix of simple rectangular plate bending element with 12 parameters expressed in explicit form is derived.
利用初始函数法，提出一种类似三阶位移模型的板弯曲方程新模型。
A new model of plate bending Similar to the model of three-order displacement is proposed by means of the method of initial functions.
“臂力”是三个扁平的压电启动器-当电流通过它时金属板弯曲。
Its "muscles" are three flat-plate piezoelectric actuators — pieces of metal that bend when electricity runs through them.
在安装板弯曲时突出结构也作为一个支点，并密封相邻板间的缝隙。
In case that the mounting plate is bent, the raised structure can also be used as a support point and seal seams with an adjacent plate.
利用坐标变换将钢筋混凝土板的弯曲问题变换为各向同性板弯曲问题。
The coordinate transformation method is used in this paper to convert bending problems of orthographic concrete plate to isotropic.
针对符拉索夫板弯曲问题的基本方程，给出了两个形式简洁的通解定理。
Two kinds of general solutions to the displacement equation for the bending problems of Vlasov plates are given in this paper.
平面弹性与板弯曲的相似性理论为构造薄板单元提供了一条有效的新途径。
A new effective way to formulate thin plate element can be realized by using the similarity theory between plane elasticity and plate bending.
经典的梁板弯曲理论由于未考虑横向剪切变形的影响而只能适用于细长梁和薄板。
Classical bending theory of beam and plate can only be fit for thin and long beam and thin due to without considering deformed influence of cross shearing.
从而其分片试验、收敛性等性质也同时移植到板弯曲元，使两者处于同一水平上。
Therefore the theories such as patch test and FE convergence etc. can be moved to plate bending, thus both sides will be on the same theoretical level.
本文分析了薄焊接试板弯曲试样失效的原因，并对减少失效的可能性作出了阐述。
The paper discusses the reasons why the welded test sample loses its efficiency and suggests how to reduce possibilities of such failure.
研究了钼板轧制工艺对成品钼板弯曲性能的影响，并通过试验找出了具有良好弯曲性能的最佳生产工艺。
The influence of the rolling process on the bending properties of the finished molybdenum sheet is studied. The best rolling process With good bending properties is found out.
钢丝绳向新的一层过渡时，对端侧板产生轴向推力，导致侧板弯曲，同时在侧板与筒壁过渡处产生较大应力。
The axial force toward the side board is always produced when the wire rope reaches the new layer. It makes the side board bended and causes very large stress between the side board and the roller.
根据疲劳试验结果，建立了预应力钢纤维混凝土板弯曲疲劳方程和剩余强度衰减方程，分析了抗弯刚度衰减规律。
According to fatigue experiment results, the fatigue equation and equation of surplus strength degradation are built. The law of degradation of flexural rigidity is analyzed.
另一面的管道地板是没有漆过的木板，两边是窄窄的砖墙。三尺宽的天花板弯曲成拱形。看上去像一个横放着的烟囱。
The crawl space beyond had a floor of unpainted, unvarnished wood, and narrow walls of brick. The three-foot ceiling was curved in an arch. It looked like a chimney lying on its side.
根据宽板弯曲过程中的变形与应力分布特征，提出了一种计算弯曲过程中板料厚度随弯曲程度变化的新的近似求解方法。
A new approximate solution to figuring out thickness reduction in bending sheets is presented in views of the characteristics of deformation and stress distribution.
根据宽板弯曲过程中的变形与应力分布特征，提出了一种计算弯曲过程中板料厚度随弯曲程度变化的新的近似求解方法。
A new approximate solution to thickness reduction of bending sheet is presented by considering the characteristics of deformation and stress distribution.
同时本文也指出了蜂窝式空心板是以平板弯曲为主的带肋的板，而密肋楼板或井式楼板则是以交叉梁弯曲为主的带板的梁系。
Meanwhile this paper points out that cellular voided plates are the plates with ribs and the ribbed or waffle plates are the cross girder system with slabs as its wingspan.
引入正交试验分析对影响激光拼焊板弯曲回弹的各参数进行了优化，试验表明，弧形顶板模具结构能有效控制激光拼焊板的回弹。
Then, orthogonal experimentation is introduced to optimize each parameter that influences the springback of laser tailor-welded blank. The result shows that the arc roof mould STR...
对宽板弯曲变形过程进行分析，提出了弯曲过程中板坯外表面半径，板料厚度和变薄系数随板坯内表面半径变化的理论解，并与查表法和近似解作了比较。
By analyzing the wide sheet bending, the variations of theoretic radius values of outer surface, sheet thickness and thinned coefficient with radius of inner surface in bending were put forward.
慢慢的弯曲你的膝盖直到你的脚板指向天花板。
Slowly bend your knees until your feet point toward the ceiling.
慢慢的弯曲你的膝盖直到你的脚板指向天花板。
Slowly bend your knees until your feet point toward the ceiling.
应用推荐