方法：采用三维有限元的方法进行试验分析。
Medthod: Test and were made analysis were made by the method of three_dimensional finite element analysis.
最后讨论了利用全变分方程建立有限元的方法。
Finally, based on the total variational equation, the finite element method of these problems is also discussed.
对轻轨车站大悬臂结构基础应用三维有限元的方法进行了计算分析。
The large_cantilever structure foundation in light rail station is studied with 3_d finite element analysis method.
对轻轨车站大悬臂结构基础应用三维有限元的方法进行了计算分析。
Study on the influence of parameters to the dynamics of light rail vehicles with independently rotating wheel;
本文采用有限元的方法模拟了典型TSOP封装产品的塑封脱模过程。
In this thesis, molding process for a typical TSOP product is studied in detail, and FEA (Finite element analysis) has been applied in this process.
方法：采用三维有限元的方法建立力学模型，并计算分析应力分布特点。
Method By FEM, the stress value and distribution were calculated and analyzed.
目的：通过三维有限元的方法观察分析人工腰椎间盘在腰椎运动节段中的应力传导作用。
OBJECTIVE: Three-dimensional finite element method was used to observe and analysis the stress conduction of artificial lumbar intervertebral disc in lumbar motion segment.
对于金属导体引起的电场不规则畸变，采用有限元的方法计算场强以验证是否超出临界值。
And finite element method was adopted to calculate the electric field strength to find whether it is beyond the critical.
在齿轮的静力学分析中，利用有限元的方法对齿轮的齿根弯曲应力和齿面接触应力进行了研究。
Bending stresses and contact stresses of the gears were investigated by finite element method in the static analysis.
方法：用三维有限元的方法对不同弹性模量和不同直径种植体植入后骨界面的初始应力进行分析。
METHODS: Three-dimensional finite element method was used to analyze the initial stress around screw implant of different elastic modulus and different diameter.
目的采用有限元的方法研究舌侧矫治过程中上颌第一磨牙牙根、牙周膜、牙槽骨应力分布的特点。
Objective To observe the stress distribution of maxillary first molar and its periodontium in lingual orthodontics.
其次用有限元的方法实现了限位装置的作用，分析比较了安装限位装置前后拉索的振动特性变化。
Effect of the device was implemented through the finite element method, comparison of the cable with and without the mitigation device was made to investigate the vibration characters of the cable.
为了更好的了解节点的受力特征，本文将对T型钢桁架节点采用有限元的方法进行一些研究工作。
To make a better understanding of joint mechanics behaviors, this thesis studies joints of T-section steel truss with finite element method (FEM).
本文对某矿112.6米的封闭式皮带走廊用有限元的方法计算了它在地震力和风力作用下的效应。
In this paper, by use of FEM, the effects of wind and earthquake action on an enclosed conveyer-belt corridor with a span of 112.6-metres has been discussed.
用有限元的方法计算了整个吊架的应力分布，在此基础上用第二类疲劳图验证了索道吊架的失效模式。
The stress state of the whole hanger is calculated by the finite element method. Then, the failure of the hanger of ropeway is also determined by the second fatigue chart.
采用试验和有限元的方法研究了离合器从动盘结构的刚度和强度，并对应力集中的区域提出了改进方案。
The stiffness and strength of clutch driven plate assembly were experimentally and numerically studied, an improvement design on the stress concentration was given.
采用有限元的方法计算分析了混凝土圆柱体在受横向均匀线荷载和非均匀线荷载时其横截面上的应力状况。
Stress distribution at cross section of transverse uniformly distributed load and non-uniformly distributed load applied to concrete cylinder by finite element method is analyzed.
采用有限元的方法对电磁铁的磁场进行了分析，并利用ANSYS软件进行了模拟磁场的计算，获得了磁场的分布。
The magnetic field is analyzed with the finite element method. The simulated magnetic field is calculated with the software of ANSYS and the distribution of the magnetic field is gained.
为了研究梯度非均匀有限板中裂纹动态响应问题，用波动有限元的方法研究了梯度非均匀板中裂纹在冲击载荷作用下的动态响应。
The wave finite element method was used to study the dynamic response under impact loading in a gradient non-homogeneous plate with a crack.
这提供了一个计算机模型，在良好的基础，特别是在有限元方法。
This provides a good grounding in computer modelling and in the finite element method, in particular.
条分法和有限元法是土质边坡稳定分析的主要方法。
Slice method and finite element method are principal methods of soil slope stability analysis.
为你自己证明这点的最好方法是生成一个简单的有限元模型，并检查输出结果。
The best way to prove it to yourself is to make a simple finite element model and check out the results.
本文成功地将机群计算应用到解决在电法勘探中使用有限元方法（FEM）时产生的大规模线性方程组问题。
This dissertation successfully used cluster computing for solving large-scale linear algebraic equations problems when the finite element method (FEM) is applied in electrical prospecting.
本文以纳米压痕法结合量纲分析及有限元方法来测量薄膜材料的应力-应变关系。
In this master thesis, the stress-strain relationships of thin films were measured by nanoindentation combined with dimensional analysis and finite element method.
本文研究了桅杆结构非线性有限元模型的建立方法。
In this dissertation, nonlinear finite element model establishment method of the guyed mast is studied.
在完成过程中，充分考虑了铺设轮的机械设计要求，采用了计算机辅助仿真设计、有限元分析和试验校验的方法。
In the process of completing, the mechanism design requests are considered fully, some methods such as the computer assistant simulation design, finite element analysis and test verify are adopted.
样机试验数据表明提供的压弯机构原理是可行的，压弯机构仿真有限元模型是可信的，这种设计方法是可靠的。
Experimentation data shows that the principle of bending mechanism in this article is feasible, finite element model of bending mechanism is credible and its design method is dependable.
自适应有限元方法在实际工程问题的分析中有重要的应用价值。
Self adaptive finite element method has its important application value in the analysis of practical engineering problems.
自适应有限元方法在实际工程问题的分析中有重要的应用价值。
Self adaptive finite element method has its important application value in the analysis of practical engineering problems.
应用推荐