该方法与最小模方法相似也引入权重矩阵。
This method is similar to the minimum norm method, a weight function is also introduced.
在本文中我们研究缺项幂级数的最小模与最大项间的关系，改进了P。
In this paper we discuss the relation between the minimum modulus and the maximum terms of gap power series, and improve the result due toP.
从复变函数理论出发，利用辐角原理、最大模原理、最小模原理给出代数学基本定理的几种新的证明方法。
This paper uses several methods of complex functions theorey to prove fundamental theorem of algebra by argument principle, maximum modulus principle and minimum modulus principle.
从复变函数理论出发，利用辐角原理、最大模原理、最小模原理给出代数学基本定理的几种新的证明方法。
The minimum modulus principle is proved by using the preserving field theorem, and the span of minimum modulus point is discussed.
刀口模切割线间的间隙最小，冲孔模修整时的分布宽度也很小，这些都是要注意的。
The gap between the minimum cutting edge cutting, trimming punching die when the distribution width is small, these are to be noticed.
设备设计师能通过审慎地选择输入输出级电路的拓扑和共模阻抗来最小化失配或“非平衡”的效应。
Equipment designers can minimize the effects of these mismatches or "unbalances" through judicious choices of input and output stage circuit topologies and common-mode impedances.
如果不采取措施将叠加到信号上的串模噪声减到最小，串模噪声会对测量产生严重的影响。
Normal mode noise can seriously affect measurements unless steps are taken to minimize the amount added to the desired signal.
在设计控制系统时，滑模控制滑模面通过最小化最优价值函数得到，控制器采用饱和控制器。
In the process of control design, the sliding surface of sliding mode control is determined by minimizing the optimal cost function, and the controller is the saturation controller.
并利用时域最小二乘法和复模圆法对实验数据进行了三维的模态参数和振型分析。
Modal parameters and vibration type were obtained by the method of least squares time domain, complex modal analysis and the experimental data.
由于口模内速度变化梯度较大，采用最小二乘近似节点控制方法来控制近似效果。
Since the gradient of the velocity is high in the mould, the control method of simulation points is applied in the least square approximation.
通过分析CDMA系统的特点，提出码滤波最小二乘恒模算法（CF-LSCMA），保证了恒模阵列能够应用于CDMA系统。
Through analyzing on the features of CDMA system, this paper advance the CF-LSCMA algorithm, which guarantees the constant modulus array could be applied in CDMA system.
使用注射成型机，最好使用最小同时充足的锁模力f。
In using an injection moulding machine, it is best to use the minimal but adequate clamping force f.
前一种算法根据最小恒模误差准则给出了求解加权矢量的新的代价函数，并使用直接搜索法计算对角加载值的最优解。
The former presents a novel cost function based on MCME criteria for the weight vector of antenna array, with direct searching method searching for optical diagonal loading value.
在离子温度梯度模（ITG）湍流背景中，通过最小自由度模型中模耦合方式产生带状流，对此模型做了动力学稳定性分析及数值求解。
The energy cascade process in the ITG mode turbulence and the relationship between Reynolds stress and zonal flow are also discussed.
采用一种修正恒模算法(MCMA)，该算法使修正的误差函数最小并且自适应学习率由接收序列即时调整。
In the paper, a modified constant modulus algorithm (MCMA) is proposed. The proposed algorithm minimizes a modified error function and the learning-rate is multiplied by received sequences.
给出了求解一类具有简单约束的上模集函数最小值问题的一种局部搜索法，并讨论了所给算法的性能保证。
The algorithm is an improved greedy algorithm which combined the part of enumeration method with the greedy algorithm, thus to make it a better performance guarantee.
针对最小方差自适应控制器的固有缺点 ，在标准最小方差控制中引入糊模控制算法来弥补其不足 。
Aiming at the intrinsic defects of minimum variance adaptive controllers, fuzzy controy algorithm is introduced into standard minimum variance control.
给出了求解一类具有简单约束的上模集函数最小值问题的一种局部搜索法，并讨论了所给算法的性能保证。
An approximation algorithm is presented for minimizing a nondecreasing supermodular set function, and its performance guarantee is probed.
硬件电路设计：89c51最小系统加上模入电路adc 0809和模出电路TLC7528；由运放构成的被控对象。
Hardware circuit Design: 89c51 minimum system together with the mold and mold into the circuit ADC0809 circuit TLC7528 OPAMP posed by the charged object. 2.
确定了锥形模膛的最小长度、模腔锥角与毛坯长度的关系；
The minimum depth of conical die and the relationship between coning of die cavity and workpiece length are determined;
确定了锥形模膛的最小长度、模腔锥角与毛坯长度的关系；
The minimum depth of conical die and the relationship between coning of die cavity and workpiece length are determined;
应用推荐