通过对故障产生原因的分析给出了故障处理方法并举例加以说明。
Software faults is the most common one of the stoppages to hard disk and often man - made Through. analysis so of the faults, this paper introduces method of handling faults by...
本文介绍ABL50型血气分析仪使用过程中遇到的电、液路故障处理方法。
The paper describes the ways to maintain the circuit and the fluid pipe of ABL50 blood gas system.
介绍了盘车装置的作用及工作原理、盘车装置故障的几种形式及故障处理方法。
This paper presents the functions and working principles of turning gear as well as the types and handling measures of faults in turning gear .
根据血压计在实际应用中的情况，对其质量检查与常见故障处理方法进行了阐述。
This paper also introduces the method of quality check for the blood-pressure meter and the troubleshooting.
该文以相分量故障处理方法为依据，提出了一种相分量坐标下的故障向量变换法。
This paper presents a new way, fault vector transformation method in phase coordinates, based on fault analysis of phase components.
在汽车行驶时，转向系经常发生各种故障，根据多年修车经验，总结如下几点常见故障处理方法。
Traveling in the car, the steering system failure occurred frequently, according to years of repair experience, summarized as follows a few common fault approach.
电压转换设备，记录了使计算机执行故障处理的程序的计算机可读记录介质，以及故障处理方法。
Voltage converting device, computer readable recording medium with program recorded thereon for causing computer to execute failure processing, and failure processing method.
介绍CA8020型双踪示波器的常见故障现象及其产生的原因，给出了关键点测量数据和故障处理方法。
The article introduces some common fault phenomena of the CA8020 type double oscillograph working and the reasons which cause them provides the measurement of the key and the methods of repair.
该文结合工程实例详细介绍了这一技术的原理、施工工艺及施工方法，还总结了特殊情况下的施工及故障处理方法。
Here, combining with engineering examples, the method is introduced in detail, including its technical principle, construction technology and procedure, trouble treating and so on.
嵌套在这个故障处理程序中的活动试图纠正这种状况，以使正常处理可在作用域外继续或使用其它方法来完成流程。
The activity nested within this fault handler tries to correct the situation such that regular processing can continue outside the scope or alternate ways to complete the process can be taken.
在这里，处理故障的单独方法也不是绝对必要的，但使用它是一项良好的习惯。
Again, the separate method for handling faults is not strictly necessary, but is a good practice.
流程内出现故障，不可能再正常执行时，可以使用故障处理程序试图寻找其他方法完成流程。
When a fault occurs within a process and regular execution is no longer possible, you use a fault handler to attempt to find another way to complete the process.
下面让我们再来看看卫星接收机的常见故障及处理方法。
Let's take a look at satellite receiver the common failures and processing method.
另外，研究了两种故障诊断的数据处理方法。
In addition, two data processing methods of fault diagnosis are studied.
最后，对堆垛机的故障诊断及处理方法进行了研究。
Last, aisle vehicle fault detection and process method are researched.
并进一步提出了通过平滑处理故障首尾数据的优化方法提高行波波头提取的可靠性。
An optimization method is proposed to improve the reliability of getting the traveling wave head, smoothing both beginning and ending data.
本文结合日常的维护经验来分析和总结常见故障的定位和处理方法。
This article analyzes and summarizes the common fault orientation and processing method combining with the daily maintenance experience.
针对过程控制仪表常见的故障现象、造成原因、判断处理的方法进行总结和分析。
The familiar fault phenomena, causes, judgment and treatment methods of process instruments are summarized and analyzed.
该方法首先利用小波变换和主成分分析对故障信号进行预处理，然后用处理后的故障特征数据对小波神经网络进行训练和测试。
The method uses wavelet transform and principle component analysis to preprocess fault signal, afterward training and testing wavelet neural network with the preprocessed fault characteristic data.
文章介绍变压器铁芯多点接地故障的诊断和处理方法。
The characteristics of transformer core multiple grounding fault are analysed, the diagnosis and treatment methods are introduced.
介绍了焦化塔底阀的结构特点，论述了焦化塔底阀使用过程中常见故障的处理方法。
Introducing the structural features of the bottom unheading valve and describing the troubleshooting method of the bottom unheading valve on the common troubles.
针对EJA智能双法兰差压变送器的具体应用情况，介绍了其典型故障的详细处理方法。
In accordance with the concrete condition of application of EJA intelligence double flanges differential pressure transmitter, typical malfunctions and their handling methods are introduced in detail.
着重介绍了安全钳在电梯中所起的作用，安全钳的结构、种类及安全钳的工作原理以及安全钳的一般检验方法，安全钳常见的故障、处理方法。
It focuses on the role of safety gear of elevator, intro-duces safety gear types and working principle of safety gear, as well as the general test methods, common safety gear failure, treatment.
就普通型带式输送机在工作中常见的故障及处理方法进行浅述，以便于大家更好的学习，服务于生产。
Taransport machine for the common type take type familiar in the work of break down and handle a method to carry on shallow say, in order to in everyone better study, service in produce.
以西门子移动交换网为例，通过实际案例分析，介绍了交换网络故障处理的方法和经验。
Taking Siemens mobile switch network for example, it introduces the method and experience of exception handling of mobile switch network through case analysis.
介绍了泵吸反循环钻进的施工特点、适用范围、施工中的技术要求与常见故障的原因及处理方法。
The paper has introduced constructional properties, applicable sphere of pumping reverse circulation drilling, and its technical demands and the reasons of common hitchs and processing methods.
对称分量法及其序网联接技术是电力系统故障处理的传统方法。
Symmetrical components method and its sequence network connection technique are conventional way on fault analysis of power system.
介绍气动标记机控制系统的组成及原理，并分析介绍了常见故障的处理方法。
The paper introduces the composition and the principle for the control process of the pneumatic marker control system.
本文介绍了仪表回路试验的方法以及常见故障的处理措施，经实践检验，该方法和措施对仪表回路的试验工作具有参考价值。
This paper has introduced common testing methods as well as fault handling measures by practice, these methods and measures have reference value for the testing work of meter loop.
介绍聚酯连续生产调和反应过程中，EG循环喷淋系统可能发生的故障及处理方法，以确保连续聚酯设备安全稳定地运行。
The possible failure and trouble shooting in the EG spray condenser circulating system are discussed in order to ensure that the continuous polymerization system can run safely and steadily.
应用推荐