附加横向钢筋是没有必要在搭接处。
Additional transverse reinforcement is not necessary in the lapping zone.
所有次要加固搭接可重叠在同一个位置。
All secondary reinforcement may be lapped at the same location.
拼接处必需清理干净，以确保拼缝搭接紧密。
Joining together must clean up, to ensure flat-fell seam lap closely.
搭接可由可以通过啮合或分层构造（图8.10）。
Laps may be made either by intermeshing or by layering of the fabrics (Figure 8.10).
因此，请用户按接头的搭接长度，确定硫化机的台数。
Therefore, the user presses the length of lap joints to determine the number of curing machine units.
简要地对比分析了相邻桩之间不同视搭接宽度的两种方案。
Two different plans of apparent connection length between near pile are briefly contrasted and analyzed.
如此估计的损失，是在极少量搭接情况下所预期的那些损失。
The losses so evaluated are those expected in the case of negligible overlap.
搭接结构悬浮控制是高速磁浮列车悬浮技术的关键问题之一。
Suspension control of the join-structure is one of the keystone of High-Speed Maglev Train suspension technology.
由搭接节点耗能分析可知，总体看来各试件具有良好的耗能能力。
It was finally known from energy consumption analysis of joints that, generally speaking, all specimens possessed good capability of energy consumption.
研究不同搭接宽度和层数对激光熔覆的显微组织及开裂性的影响。
This article discusses the influence of microstructure and cracking behavior in laser cladding with different repetition width and different layers.
对铝合金L F3Y 2搭接板进行了热压条件下激光深熔焊接。
Deep penetration laser welding was performed at aluminum alloy LF3Y2 under hot and press condition.
叠门；搭接：顾名思义搭接就是将一片衣片缉缝到另一片衣片上去。
Lapping: As the name suggests one section is lapped over a second section.
凡两个钢筋交错接触，并在粘结条件好的情况下，这搭接不能捆绑。
Where two touching bars are positioned one above the other, and where the bond conditions are good, such bars need not be treated as a bundle.
特别是木材的细节部分，例如工人在梁截面部分解决了斜搭接的问题。
Timber details such as scarf joint were resolved with the builder to be applied in the beam section.
材料内部的损伤引起相互搭接的渗流网络破坏，而致使材料电阻增大。
The damage occurring inside materials causes breakdown of percolation network and brings an increase in electrical resistance.
阐述了阀门电动装置运行现场导线搭接的常见问题与搭接工艺的改进。
Describe the usual problems of lead lap joint about valve electric actuator when working and the improvement of joint process.
别墅包覆着搭接的涂油可回收红柳桉树，随着时间的流逝会被自然风化。
It is clad in lapped and oiled recycled jarrah and is left to weather naturally over time.
本文介绍一种具有速度显示，环缝搭接量精密控制的高精度焊接工作台。
The high Precision welding bench with speed display and control of girth lap behavior are described.
离聚体的拉伸强度、搭接剪切强度和乳化性能均随顺酐化程度的提高而改善。
Tensile strength and lap shear strength increased with increasing of grafting degree due to great improvement of polarity.
根据搭接焊缝偏中距离和焊缝高度的计算方法提取信息，实现焊缝的自动跟踪。
According the calculation method of overlap joint's offset and height, the information was acquired and seam tracking was realized.
增加横向钢筋应均匀分布在锚固区和搭接的间距应不超过5倍的纵向钢筋直径。
The additional transverse reinforcement should be uniformly distributed in the anchorage zone and the spacing of bars should not exceed 5 times the diameter of the longitudinal reinforcement.
当纺丝液溶剂为高沸点溶剂时，纤维间易产生搭接，导致无纺布网孔直径减小。
The fiber of membranes was easily connected each other when high boiling solvent was used, which make the porosity diameter smaller.
根据协调设计的特点和搭接网络的要求，建立起适合于协调设计的搭接网络模型。
According to the characteristic of coordination design and the need of lapping network, the lapping network model suitable for coordination design was built.
在总结了搭接柱转换结构各组成部分的受力变形特征后，提出了相应的设计建议。
Comprehensive discussions on all parts of conversion column bracket have been made and corresponding Suggestions for design have been recommended.
电流、焊接速度、压力等参数都会影响窄搭接焊机在镀锌机组生产中的焊接质量。
Current, welding speed, and pressure are the factors which can influence the welding quality of narrow lap welding machine during the galvanizing unit production.
扁钢与扁钢焊接应采用搭接焊，搭接长度至少为扁钢宽度的2.5倍，且至少3边焊接。
The overlapped length should be at least 2.5 times of the width of the flat steel, and at least 3 edges need to be welded.
两块板端应该搭接，搭接长度大约为工厂预制槽的一半(搭接时注意当地的常年风向)。
Two boards should end lap, lap length about half the prefabricated groove for the factory.
采用激光熔覆搭接技术，在中碳钢基体上制备出原位析出的颗粒增强金属基复合材料表层。
Metal matrix composite layer reinforced in situ ZrC particles was formed by laser cladding overlapping on the medium carbon steel.
采用激光熔覆搭接技术，在中碳钢基体上制备出原位析出的颗粒增强金属基复合材料表层。
Metal matrix composite layer reinforced in situ ZrC particles was formed by laser cladding overlapping on the medium carbon steel.
应用推荐