二是运动控制卡的驱动程序设计。
The second is the driver design for the motion control card.
控制卡可以指出程序是在主系统带上还是其他卡片上。
The control card may indicate that the program is on the master system tape or on CARDS.
对运动控制卡的部分重要软件接口进行阐述和程序设计。
Then this paper represents some important software interfaces and it's programs.
硬盘驱动器组件包括硬盘驱动器、电力电缆、数据电缆、控制卡等。
Hard disk drive components including the hard drive, a power cable, a data cable, and the controller card. If an error message indicates there is a hard disk problem, try following these steps.
实践表明该控制卡能满足运动控制部分的精度及速度要求。
The practice proves that this board can satisfy require of motion control on precision and speed.
运动控制卡是可以广泛应用于运动控制系统的上位控制单元。
The motion control card is extensively applied in the high-level control unit of the motion control system.
本课题的关键是GPIB控制器和通道控制卡的软硬件设计。
The key point of the project is software and hardware design of GPIB controller and channel controller.
论述一种新型的CAN总线PC控制卡的设计原理和实现方法。
This paper discusses the principle and implementation of a new type of CAN bus PC controller card.
通过多任务实时软件代替运动控制卡，完成实时伺服控制任务。
Motion control boards were displaced with multitask software to perform the servo controlling motion accurately.
该显示控制卡可以控制全类型LCD，并且支持多种微控制器。
The display control card compatible with all kinds of LCD and its bus interface support many kinds of MPU.
步进电机控制卡的设计采用了DSP技术和高速pci总线技术。
The design of step motor control card is based on DSP technique and PCI bus technique.
论文在给出整体的结构框架后，详细介绍了控制卡的硬件软件组成。
After the block diagram discussed, the hardware and software structure are demonstrated, the designs of the circuits based on the motor control chip.
提出一种基于PC和运动控制卡的开放式运动控制系统的设计方案。
A design of the open motion control system based on PC and motor control card was presented.
硬件由微机、步进电机控制卡、步进电机驱动器和步进电机等器件组成。
Hardware consists of microcomputer, stepping motor control card, stepping motor driver and stepping motor and so on.
实验证明，该运动控制卡运行稳定、实时性好，能满足运动控制的要求。
It is proved by the experiment that the control card has good real-time performance and stability, which can meet the requirements of motion control.
控制卡识别程序的来源，所有磁带的种类，并且在需要的时候识别库磁带。
The control card identifies the source of the program, the category of all tapes, and the identification of library tapes when required.
讨论了基于运动控制卡的火焰切割机数控系统的软件设计中多线程技术的应用。
This article discussed the multi-thread technology application in numerical control system software design of flame cutter based on the movement control card.
设置运动控制卡中的参数，通过控制卡发出的脉冲与方向信号来驱动伺服电机。
By the parameters, the pulses and the direction signals of the control card, the servo motor is drived.
关键(特殊)工序控制卡，由制造部门负责编制，并负责工序控制和工序质量分析。
The Manufacturing Department is responsible to formulate the critical (special) process control card, to control the process, and to analyze the process quality.
同一个程序的后续作业中不能包含程序控制卡或者(如果适用的话)二进制卡片程序。
Subsequent jobs in sequence for the same program must not contain the program control card or (when applicable) the binary card program.
系统在硬件上通过一台工业计算机，一块DSP运动控制卡来实现机器人的运动控制；
The hardware of system uses a PC and a DSP motion control card which complete motion Control.
开发了由PMAC运动控制卡和工业PC机组成的开放式多功能激光模切加工数控系统。
An open and multifunctional laser die-cutting numeric control system was developed with PMAC motion control card and industry PC.
并以基于PC和运动控制卡的开放式四轴数控系统实现支管端头的变角度焊接坡口面切割。
The open four-axis CNC system based on PC and motion control card can accomplish the cutting of various-angle welding plate.
此实验装置以PC加运动控制卡作为上位控制单元，具有数字化、集成化、开放式的特点。
This system uses PC and motion control cards as the upper control unit. It is digitized, integrated and open.
相对于LED大屏幕显示器视频控制卡，脱机控制卡在软件实现上需要做较多复杂的工作。
Software realization of LED Large Screen Display Offline Control card needs much complex work compared with that of video card.
应用国产MCT8000运动控制卡开发了一种新型产业化的开放式结构机器人控制系统。
Using a homemade motion controller marketed as MCT8000 series, a universal robot controller with open architecture has been developed.
介绍自行研制的基于80C196KC单片机的交流伺服电机控制卡的硬件设计及其软件实现。
The paper introduces the hardware and software design of an AC servo motor control card based on 80C196KC.
文中重点叙述了MPC02运动控制卡、松下交流伺服电机和驱动器及工控机组成的硬件系统。
The hardware system that composed by MPC02 card, Panasonic AC servo motors and their drivers was mainly discussed.
该试验台采用了商品化的微型工作台、高速空气涡轮主轴、直线型超声电机和基于PC的控制卡。
The test-bed utilizes commercially available micro stages, a high-speed air turbine spindle, and linear ultrasonic motors and PC-based control board.
该试验台采用了商品化的微型工作台、高速空气涡轮主轴、直线型超声电机和基于PC的控制卡。
The test-bed utilizes commercially available micro stages, a high-speed air turbine spindle, and linear ultrasonic motors and PC-based control board.
应用推荐