目的考察溶剂分散和挤压器联动装置制备脂质体药物制剂的工艺条件、可行性和适用范围。
OBJECTIVE To apply the solvent dispersion technique and extruding linkage device as a feasible and suitable method for the preparation of liposomes.
可分离的冷却塞和停机程序包括将任何多余的塑料容纳在冷却塞和挤压器之间生成的空隙中。
The separable cooling plug and shutdown procedure includes accommodating any excess plastic in a created void between the cooling plug and the extruder.
目的：介绍采用骨挤压器从牙槽嵴顶入路提升上颌窦底后植入种植体，观察该方法窦底提升后种植的临床效果。
Objective: Introduce the use of osteotomes to elevate the sinus floor from alveolar ridge at the time of implant placement .
具有专业生产五金模具及制品、铝合金面板、散热器、铝合金挤压模具、深加工、氧化着色处理的优势。
Having advantages of specializing in hardware molds, aluminum alloy panels, radiators and aluminum extruding molds, deep processing and heat tinting treatment.
对传感器的挤压发生非常微小的变化就能引起大量的电子流，因此传感性相当敏感。
Minuscule changes in the squeezing of the sensor trigger far larger changes in the flow of electrons, which makes the sensor extremely sensitive.
很有可能使用制造挤压空气这样相同的机械能来产生电能去为滑翔器电池充电。
It may well be possible to use the same mechanical forces that produce compressed air to generate electricity to top up the glider's batteries.
正在进入服务器市场的思科将会使得这一块的利润空间被挤压的更厉害——尤其是当服务器同时成为储存和网络机柜的时候。
With Cisco Systems entering the server market, the profit margins could be squeezed — especially if the server essentially becomes a storage and networking box too.
图3显示了呈现XML结果的浏览器，这些XML结果作为各种各样的web页面返回，不过看起来不美观，挤压在一起并且没有任何格式。
Figure 3 shows the browser displaying the XML results returned as a kind of web page of sorts though it looks ugly, squished together and not at all formatted.
生产封隔器的膨胀可能通过挤压位于两个盘子之间的弹性部件(有些象汽车轮胎形状)来完成，迫使侧边向外膨胀。
The expansion of the former may be accomplished by squeezing the elastomeric elements (somewhat doughnut shaped) between two plates, forcing the sides to bulge outward.
双传感器的检测区域足够狭窄，因而不会产生挤压点导致操作人员受伤，或冰块、灰尘形成的堵塞。
Thanks to the narrow detection area of the double sensor, there is no danger of a pinch point causing harm to the operator or allowing clogging from ice or dirt.
本文根据铅的刚塑性本构关系，利用均匀塑性变形能法，推导了铅挤压阻尼器的阻尼力滞回模型。
Based on the rigid plastic constitutive equation of lead, the damping force model of lead extrusion damper was deduced from the even plastic deformation energy method.
柴油和水经过机械乳化器的挤压和剪切作用变成较细的乳化油，然后经超声乳化器的空化作用进一步细化。
Diesel oil and water turned into thin emulsified fuel with the shear and extrusion in the mechanical blenders, and then became thinner with the ultrasonic cavitations.
本文研究了带挤压油膜阻尼器(SFD)的转子系统在考虑弯扭耦合的情况下的加速响应。
This paper investigated the response of rotor system supported on Squeezed Film Damper (SFD) under acceleration.
介绍了实体轴承保持器的生产现状，研究了保持器的等温挤压成形工艺，并介绍了相关模具设计。
The paper introduced the situation of producing solid bearing cages and studied the isothermal temperature extrusion technology and die design.
对双盘悬臂柔性转子-非同心型挤压油膜阻尼器（SFD）系统进行了非线性动力学分析。
We used Poincare map and bifurcation map to analyze the nonlinear dynamic response of a eight degree of freedom rotor system with two disks supported on a squeeze film damper(SFD) as shown in Fig.
采用塑性成形有限元分析软件DEFORM3D，对汽车启动器套筒冷挤压齿部成形过程进行了数值模拟。
Numerical simulation on cold extrusion process of automobile starter socket has been carried out by using the software DEFORM3D.
在实验的基础上，研究了挤压油膜阻尼器的结构参数诸如偏心率、油膜的径向间隙比和承载长度等对气穴现象的影响。
The effects of structural parameters of Squeeze Film Damper (SFD), such as eccentricity, radial clearance and land length etc. on cavitation were investigated experimentally.
食物原料“墨水”必须是便于从注射器中挤压出来的液体，可以是液体奶酪、巧克力和蛋糕面糊。
The inks are currently limited to "anything that can be extruded from a syringe" - such as liquid cheese, chocolate and cake batter.
紧凑的铜质清洁网，用于清洁断路器板和塑料挤压中的进给螺杆，注塑成型工业。
Knitted copper cleaning mesh. Used for the cleaning of breaker plates & feed screws in the plastic extrusion & injection molding industry.
分析了同心型挤压油膜阻尼器的流体惯性力对柔性转子的双稳态响应的影响。
This paper investigates the influence of fluid inertia forces on the double stable response of squeeze film damper (SFD) supported rotor.
齿轮减速器的出轴与负载连接时不能重力敲打、挤压，以免造成内部变形走位，产生严重噪声或卡死现象。
No beat or squeeze when connect load to the outer axis of gear speed reducer so that not to arise deformation and dislocation, bad noise or locked dead.
挤压油膜阻尼器设计不当，会导致功能失效。
If the squeeze film damper is not designed properly, that will be caused the failure of attenuating vibration.
本文研究了支承在挤压油膜阻尼器上的转子系统碰磨故障特征的提取方法。
A method for extracting the features of rub and impact in rotor systems supported on squeezed film dampers is studied in this paper.
分析了散热器型材的结构特点，设计了挤压模具，并介绍了模具的加工工艺。
Analyzed structure characteristics of the radiator section material, designed the extruding die, and introduced the extruding die's manufacture process.
数字是用文字样条线配合挤压修改器做出来的，然后在钟表表面进行阵列。
The Numbers are a text spline with an extrude modifier, and then an array over the clock's surface.
不同种类的阻尼器(如挤压油膜阻尼器、金属橡胶阻尼器、橡胶阻尼器等)在实际应用中有着很好的效果。
In different types of dampers such as squeeze oil film dampers, metal rubber dampers and rubber dampers have found successful applications.
研究了在微梁谐振器结构中，梁作高阶振动时挤压气体薄膜的阻尼效应。
The squeeze film damping effects on beam shaped micro resonator was studied.
同时，通过试验确定了精镗孔挤压液膜阻尼器部分结构参数，为阻尼器的优化设计提供了重要依据。
At the same time, structure parameters of SLFD are confirmed through experiments and the important gist is provided for optimal design of the damper.
同时，通过试验确定了精镗孔挤压液膜阻尼器部分结构参数，为阻尼器的优化设计提供了重要依据。
At the same time, structure parameters of SLFD are confirmed through experiments and the important gist is provided for optimal design of the damper.
应用推荐