请进入BIOS设定恢复设置。
您可以将故障恢复设置为自动处理Domino服务器崩溃。
You can set up fault recovery to automatically handle Domino server crashes.
一旦发现自己的手机被该病毒感染，应立即备份手机内的重要数据，然后通过送修恢复设置清理该病毒。
If your cell phone got infected, backup important data immediately and send it back to repair, clearing the virus by restoring the system of your cell phone.
通过将它设置成“RECOVERY”来启用它，从而允许数据库管理器使用前滚恢复方法。
Enabling it by setting it to "recovery" allows the database manager to use the roll-forward recovery method.
如果其他站点或服务器也必须把您的灾难恢复服务器输入它们的安全设置，有DNS记录会有帮助。
Having a DNS record can help when other sites or servers must also enter your disaster recovery server into their security Settings.
在此对话框中，单击启动故障恢复下的设置按钮。
手动对等恢复处理不是缺省设置，必须通过配置才能进行。
Manual peer recovery processing is not the default setting and must be enabled through the configuration.
接下来，把灾难恢复IP地址通知其他职员、分部、厂商和合作伙伴：当前在其安全设置中包含您的主ip地址的所有实体。
Next share the disaster recovery IP address with any other employees, divisions, vendors, partners: any entity that currently has your primary IP address in its security Settings.
这种恢复并不会导致系统或应用数据的丢失，也不会丢失设置，甚至连缓存都不会丢失。
This recovery is done without losing system or application data, without losing Settings and even without losing the cache.
所以，你对运行有些保证，那就是，在这一带，你的警报设置点能够引发，你去保持在你的运行限制内，你能够恢复稳定的运行状态。
So you have certain margins of operating which would be in this band and your alarm set points kind of trigger you to keep within your operational limit and you can restore to steady state operation.
如果启动该设置，服务器在重启后，只可用于对等恢复处理。
If the setting is enabled, servers are only available for peer recovery processing after they are restarted.
如果拥有特定于硬件的定制驱动程序，那么可能需要恢复到默认设置或者尝试兼容的硬件支持。
If you have custom drivers specific to your hardware, you may need to revert to default Settings or try compatible hardware support.
自动对等恢复处理是启用HA时的缺省设置。
Automated peer recovery processing is the default setting when HA is enabled.
对于向导的其余步骤（选项、性能、调度和总结），可以使用默认设置；因为这些步骤与离线恢复相似，这里就不重复解释了。
You can use the defaults for the rest of the wizard steps, Options, Performance, Schedule, and Summary, which I won't repeat as they are similar steps to offline restore.
在交互会话或批处理输入结束时，这些设置恢复为它们的原始值。
The Settings revert to their original values when the interactive session or batch input ends.
这些属性可以在管理员控制台进行设置，因此，中介可以恢复配置和其它可能影响消息处理的属性。
These properties can be set using the administration console so that a mediation can retrieve configuration and other properties that may affect the processing of the message.
最糟糕的情况是，由于灾难而需要启动灾难数据中心时，却发现在灾难恢复中未设置某些项目。
The worst time to find out that there is something missing in your set up for disaster recovery is when you need to start up the disaster data center because of some disaster.
它还清除掉系统还原设置，使其难以恢复系统。
It also wipes out the system restore with a reset, making it harder to recover the system.
在设置测试环境或灾难恢复站点时，这是常有的需求。
This is a quite common requirement for setting up a test environment or a disaster-recovery site.
设置手动恢复所需的配置步骤在以下列出。
The configuration steps that are required to set up manual peer recovery are listed below.
可以在WebConfig的Backup页面中修改这个作业的设置、运行未安排的备份或恢复数据。
You can modify the Settings for this job, run unscheduled backups, or restore data from within WebConfig's backup page.
因此，要恢复到Linux 系统，需要回到前面的设置过程，并设置它默认从OtherOS引导。
So, to boot back into Linux, you'll have to go back into the settings and set it to boot the Other OS by default.
我们还将以一种特别方式设置devfsd(设备管理守护进程)，用它来备份和恢复任何对设备许可权和所有权的更改。
We're also going to set up devfsd (the device management daemon) in a special mode so that it backs up and restores any changes to device permissions and ownership.
在回滚保存点时，所有已登录的temp表—数据和模式—都被恢复到设置保存点之前的状态。
On rolling back to a savepoint, all the logged temp tables - data and schema - are restored to their states prior to setting the savepoint.
最后，如果需要恢复系统默认设置，那么应该发出命令resetdbcfg for
Finally, if you need to go back to the system default settings, issue the command reset db cfg for
当然，如果你恢复你的iPhone，所有的媒介和数据将会被删除，同时所有设置将要被重置-因此你需要尝试去恢复前首先做一个备份，如果你能做到的话。
Of course, if you restore your iPhone all your media and data will be deleted, and all settings will be reset - so you need to try to restore to back up first., if you can.
是否某些做法对你的iPhone是错误的，你能够要么尝试你自己修理它，要么重启你的iPhone-但是有时候恢复它的出厂设置是唯一真正的修复方法。
If something is wrong with your iPhone, you can either try to fix it yourself, or reset your iPhone - but sometimes restoring it to its factory Settings is the only way of truly fixing it.
不完全恢复将要求通过发出AlterDatabaseOpen Resetlogs命令来重新设置日志。
Incomplete recovery will require a reset of the logs by issuing Alter Database Open Resetlogs command.
该管理系统能够提供决策、系统设置、前台收银、仓库管理、财务分析、备份和恢复等主要功能。
This system can provide decision-making, system-setting, accounting, storage-managing, finance-analyzing, back-up, restore, etc.
该管理系统能够提供决策、系统设置、前台收银、仓库管理、财务分析、备份和恢复等主要功能。
This system can provide decision-making, system-setting, accounting, storage-managing, finance-analyzing, back-up, restore, etc.
应用推荐