然而，对于模因来说，准确性却不是很重要的因素。
这很重要，首先，让文字在mac上和Windows上显示一模一样是不可能的，不过，如果你遵从的是适应性设计，这将不会成为问题。
Firstly, it guarantees that it is essentially impossible to have text look identical on Macintoshes and Windows based systems. But if you embrace the adaptability philosophy it doesn't matter.
仿真结果表明：开关磁阻电机的智能滑模变结构控制方法简单，有良好的动态性能，较好的鲁棒性。
The simulation results show that the method of intelligent sliding mode Variable Structure Control is simple, with good dynamic performance and robust property.
出色的流动性还减少了模垢和模具磨损现象，从而降低了维护成本，延长了工具使用寿命，因而降低了工具的摊销成本。
Superior flowability also provides for a reduction of in-mould deposits, lower mould wear resulting in lower maintenance cost and longer tool life, and therefore lower amortization cost of the tool.
动模试验结果证明了该方法的有效性和可行性。
The results of dynamic simulation verify the feasibility of the proposed method.
由于长周期光栅在较高次包层模谐振时的特殊性，在光栅制作的过程中会出现与其它包层模谐振不同的特性。
Since the characteristics of higher order cladding mode resonances are specific in LPG, it will exhibit different phenomena during the process of grating manufacturing.
仿真结果表明，滑模变结构控制的性能优于常规的PID控制，在系统参数变化时表现出更强的鲁棒性。
Simulation results show that the controller is better in comparison with traditional PID controller, and it has stronger robustness for the change of system parameters.
研究指出，拥有一模一样的二重身的可能性比你想象中的要小。
According gto the research, having an exact doppelganger is less likely than you might think.
如果分模面不能在单一平面，利用设计的对称性来减小侧向推力不失为一种好方法。
If the parting line cannot be on a single plane, then it is good practice to use symmetry of the design to minimize the side thrust forces.
滑模变结构控制是一种非线性控制方法，对系统的参数变化和扰动具有安全的自适应性。
Sliding mode variable structure (SMVS) is a nonlinear control method, which is adaptive to disturbance and parameter variations.
低碳钢适用于以下情况：工具机身，把手，模座及其它不要求强度和耐磨性的类似情况。
Low carbon steels are well suited for the following applications: tool bodies, handles, die shoes, and similar situations where strength and wear resistance are not required.
增益材料放置的对称性导致奇数阶纵模的损耗，从而增加了微激光器的调谐范围。
Certain symmetry in the allocation of gain material leads to depletion of odd longitudinal modes that, in turn, increases the tunability range of the microlaser.
理论分析和实例验算证明了网络模矢方法的合理性、有效性和通用性。
Reasonableness effectiveness and currentness of the NAPS method are proved by theoretical analysis and checking up the computer time in a real case.
这个分配性条件可减弱为所谓性的条件，一个格称为模格。
This is a weakening of this distributivity condition, called modularity.
这个分配性条件可减弱为所谓性的条件，一个格称为模格。
This is a weakening of this distributivity condition, called modularity .
一些汽车在火焰，和23个人破坏性的碰撞一钢模中被卷入。
Several cars are engulfed in flames, and 23 people die in the devastating collision.
模对铸件完整性的影响。
通过实践分析讨论了冲裁模间隙的最佳取值，并给出了冲裁模设计用参考性数据和方法。
By experimenting, analyse the optimum value's choice of blanking clearance, and give some referred data and methods for die's design.
实验结果证明，该滑模控制系统具有良好的鲁棒性和快速的动态响应速度。
Experimental results validated that the presented control scheme has the merits of perfect robustness and fast dynamic response.
是科学模写的能动性使问题得到严谨的解释，并最终使我们在认识上扫除了相对论中“逻辑循环”问题的阴影。
It is through the motility of scientific duplication that the problem was given precise explanation and the shadow of "logic circulation" in epistemology was eliminated ultimately.
共模故障是电力系统可靠性评估中常见的一种故障模式。
Common mode failure is a frequently occurred fault mode in the power system reliability evaluation.
文章对线路维护工程中的光缆线路障碍查找、光纤衰减均匀性、光纤接续和偏振模色散（PMD）等问题进行了分析。
This paper discussed the trouble shooting, attenuation uniformity of optical fiber, optical fiber splicing and PMD problem in the maintenance of optical fiber line.
介绍了消失模铸造的优越性、所用原材料、常见缺陷、工艺技术问题，并指出了其发展前景。
The superiorities, the raw materials, the common shortages and the problems of technique of EPC are introduced, and points out its developmental prospect.
运用可靠性设计原理， 对塑料注射模常用的斜导柱式抽芯机构进行分析。
By using the principle of reliability design, the withdrwal core mechanism with bevel lead column in plastic injection mould is analyzed.
利用固有值和固有矢量的方法解出了耦合模方程，并对其进行理论性分析。
We have obtained the coupled-mode equation by using the eigenvalues and eigenvectors, and given a theoretical analysis.
此二法均能很好地应用于大数据序列主成分模的显著性检验。
The two methods are good to be used for the eigenvalue significance tests of large data sets.
针对冲裁模设计中的知识特点，采用专家系统进行冲裁模设计中的工艺性参数计算。
According to the view of press die knowledge, this paper, using the expert system, reasoning parameter of blanking technology in the press design.
针对冲裁模设计中的知识特点，采用专家系统进行冲裁模设计中的工艺性参数计算。
According to the view of press die knowledge, this paper, using the expert system, reasoning parameter of blanking technology in the press design.
应用推荐